![]() |
|
#1
|
||||
|
||||
![]() Quote:
That is a generous offer ! I will see how I go .... I might try making a thermo housing with a BSP threaded fitting . Aluminium would be OK to use for this job . BSP fittings are ubiquitous and most hardware stores have stock . The lower hose is 1 3/4" I think ? When I pulled down this 216 engine, the original brass bellows thermostat was still in situ with a 1940 date on it , stuck in the open position . The new thermostat I put in , in 1998 , has corroded away and collapsed . BTW these new aluminium radiators are prone to corrosion by a chemical/electrical reaction. The coolant can act as an electrolyte and the whole thing turns into a battery ! Good grounding is required to reduce this problem .
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad |
#2
|
||||
|
||||
![]()
hey dave motto
I will take that GMC thermo top housing, if you can find one ![]() The mod I had in mind is just too difficult . The GMC top housing should do the trick . The Toyota 2F engine is based on a chevy engine .... a quick search found this ............ looks similar to a chevy housing but the price is ridiculous . http://www.ebay.com.au/itm/TOYOTA-F2...item230d8e5c3d Thanks Mike
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad Last edited by Mike K; 17-06-15 at 02:54. |
#3
|
||||
|
||||
![]()
Did some more looking .
Well, it seems that any early Holden V8 or chevy V8 eg 350 327 thermo housing top will fit the old 216 ![]() Even the chrysler 318 V8 housing will fit . I wandered down to the neighbour and checked his V8 engines out with the old 216 thermo housing.. all are the same bolt pattern I will buy one on epay ..... Mike
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad |
#4
|
|||
|
|||
![]()
OK Mike.
I did sort out a GMC thermostat housing upper section and it is 1-1/2" diameter where the hose fits on. I will put it back on the shelf. Dave
__________________
Hell no! I'm not that old! |
#5
|
||||
|
||||
![]()
Mike,
Looks like the trusty old C8 is getting a thorough make over ![]() Found this radiator for sale - forgive my ignorance, but could it be a Chevrolet one? Thanks, Hanno
__________________
Regards, Hanno -------------------------- |
#6
|
||||
|
||||
![]() Quote:
Not sure , but it does appear to be the same shape as the repro Chevy HOT ROD radiator I bought recently . It could be from a 1930's era Chev truck , the hose outlets do match up with Chev . The rounded top tank indicates a early 30's design to me . Just a guess .
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad |
#7
|
||||
|
||||
![]() Quote:
I forwarded the ad to a fellow MLU member restoring a C8. H.
__________________
Regards, Hanno -------------------------- |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
For Sale: Morris Commercial Piston Liners | Andrew Rowe | For Sale Or Wanted | 0 | 24-09-14 09:23 |
For Sale: piston-ring-pin: Chevrolet Canada/US | Dirk Leegwater (RIP) | For Sale Or Wanted | 0 | 29-08-12 16:48 |
Make your own piston rings | Mike K | The Restoration Forum | 0 | 11-08-11 14:45 |
Wanted: Piston for Chev Engine | Willanthry | For Sale Or Wanted | 21 | 15-07-09 14:40 |
Piston Rings | ron | The Restoration Forum | 8 | 25-01-09 11:45 |