|
|
|
|
#1
25-02-10, 17:08
|
||||
|
||||
More of the truck, less of me
__________________
Pax Vobiscum.......may you eat three meals a day & have regular bowel movements. 
|
|
#2
25-02-10, 20:40
|
|||
|
|||
|
3rd video & cutting holes
Hi Tony
Third video is great, and concerning your earlier post on cutting holes. One of the tricks I use for cutting holes 1/4 to 3/4 in canvas, webbing, gasket material, paper, leather is by making up spin punches of various sizes. These are made from thin tubing any thing that can be fitted into the chuck of the drill press or hand drill. Just sharpen the cutting edge with a file by spinning the tube in the drill and lightly holding the file against the tube at an angle. Then you can cut holes in almost any soft material by laying in on a soft piece of wood and lightly pushing the spinning punch against the material. I've found that the drill press works best, particularly if set at a higher speed, cuts a nice clean hole. Every now and then you have to stop and clean out the hole cuts in the tube. I've even used rifle cartridges not as many cuts without re-sharpening as steel tubing. But with lots of old spent .44 and .303 casings around to use up why not, the spinning cartridge casing in the drill cuts a much neater hole then firing the bullet through the material. Cheers Phil
__________________
Phil Waterman `41 C60L Pattern 12 `42 C60S Radio Pattern 13 `45 HUP http://canadianmilitarypattern.com/ New e-mail Philip@canadianmilitarypattern.com
|
|
#3
25-02-10, 20:47
|
|||
|
|||
|
Nice Videos..
Quote:
..Those are great vids Once you get on to double clutchin' you can chomp a big fat cee-gar and double clutch your way to Hollywood.. Fine camera work too.. Keep them up ....Have you got a manager and an agent yet..??    
__________________
Alex Blair :remember :support :drunk:
|
|
#4
05-03-10, 04:27
|
||||
|
||||
|
An update
Howdy all,
Well the truck is in at Wagga getting an exhaust system fitted. As close to original as possible. Its raining a the moment so I'm catching up on some sleep after some very very long days these past 3 months. So I thought I better post some photos of what's been going on while I have a spare second. Thanks to Howard for his help this late Tuesday night and for taking the photos. Good grief I'm getting thin up top!!!! 
__________________
Pax Vobiscum.......may you eat three meals a day & have regular bowel movements.
|
|
#5
05-03-10, 04:32
|
||||
|
||||
|
And more
More pictures - luckily had very smooth run with putting this in and with the coachwork timber as well.
__________________
Pax Vobiscum.......may you eat three meals a day & have regular bowel movements.
|
|
#6
05-03-10, 04:40
|
||||
|
||||
|
A few more
Finally something Ive been meaning to do for a while..........post the ID plate.
Engine number is 2G40647F
__________________
Pax Vobiscum.......may you eat three meals a day & have regular bowel movements.
|
|
#7
07-03-10, 00:55
|
||||
|
||||
|
At last
http://www.youtube.com/watch?v=JkZRt2cw9UE
Here she is fellahs................ on the road & honking!!!!
__________________
Pax Vobiscum.......may you eat three meals a day & have regular bowel movements. Last edited by Ganmain Tony; 07-03-10 at 01:17.
|
|
#8
07-03-10, 01:20
|
||||
|
||||
|
Some stills
Some photos as well.......
__________________
Pax Vobiscum.......may you eat three meals a day & have regular bowel movements.
|
|
#9
07-03-10, 01:40
|
||||
|
||||
|
Quote:
Looking good Tony ! Hope you get it down to Corowa for the show.
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor
|
 |
|
|
Hybrid Mode
