MLU FORUM  

Go Back   MLU FORUM > GENERAL WW2 TOPICS > The Wireless Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 16-05-22, 17:44
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default

Before I plod along any further, I just want to correct an error on my part in terminology.

Over the last few posts on the three screw terminal panels, I had been referring to the fittings attached to these panels as ‘Ring Terminals’. I became suspect of that identification this morning and decided to confirm what they are more closely.

As per the attached photo, these fittings are actually ‘Fork Connectors’, but of a type I cannot recall ever seeing a modern equivalent of in any electronic supply shops today. Note that the inner throat of the fork is designed to also serve as an integral lock washer.


David
Attached Images
File Type: jpg WS No. 52 Sender 106.JPG (241.7 KB, 0 views)
Reply With Quote
  #2  
Old 26-05-22, 18:37
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default

A short and good week so far.

I received a phone call from Anything Custom, a local machine shop, on Tuesday advising two small items I had asked them to fabricate for this project, were ready for pickup.

This particular item used to be a 3.5-inch long piece of ½-inch copper water pipe. I needed it to be pressed flat to form a small copper buss bar that will serve as the key part to a Ground Terminal for my wireless equipment.


David
Attached Images
File Type: jpg Ground Terminal Project 1.JPG (284.4 KB, 0 views)
Reply With Quote
  #3  
Old 26-05-22, 18:52
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default

Going all the way back to the 1970’s, I have never bothered hooking my two Wireless Sets No. 19 to a Ground Terminal when operating them, in spite of recommendations to do so in the various 19-Set manuals. My excuse was always that it was too much work to run a proper Ground Line into the part of the basement the wireless equipment was set up in.

That changed a couple of years back when the bathroom next door was renovated. I actually took the time to take advantage of opened walls and ceilings to run a continuous transmission cable in from the aerial in the back yard to the wireless equipment, and also a proper ground line. As far as I got at the time with the Ground Line was a foot long lead of copper wire poking through the wall under my wireless bench and a running idea of how I wanted two related terminals set up.

With the 52-Set being the powerhouse it is, I finally caved and decided to get this Ground Terminal completed and ensure all future operation of either the 19-Sets, or the 52-Set will be done with the equipment properly grounded.

So, in addition to the piece of water pipe that has now been flattened, the attached brass hardware and 4-inch square, plastic electrical box have been added to the parts to complete this Ground Terminals sub-project.


David
Attached Images
File Type: jpg Ground Terminal Project 2.JPG (178.8 KB, 0 views)
File Type: jpg Ground Terminal Project 3.JPG (267.0 KB, 0 views)
File Type: jpg Ground Terminal Project 4.JPG (257.3 KB, 0 views)
Reply With Quote
  #4  
Old 26-05-22, 19:48
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default BOXES, Tool, No. 1 WS Cdn No. 52 ZA/CAN 4727

This was the second small item I had fabricated at Anything Custom.

It is a replica of the bracket removed from the right rear wall of the tool box and it would have supported the right hand end of the wooden Hydrometer Storage Case.

Once I have drilled the mounting hole and given the bracket an aged patina I will install it.

I you want to recap the story of this tool box, I starts with its discovery and arrival back in May, 2018 (Posts #65 - 69), refabrication of the missing wooden partition (Posts #321 - 323), in 2020 and a test fit of the Irons, Soldering in Post #403.


David
Attached Images
File Type: jpg WS No. 52 Cdn, Box, Tools S.JPG (238.0 KB, 0 views)
File Type: jpg WS No. 52 Cdn, Box, Tools T.JPG (186.7 KB, 0 views)
File Type: jpg WS No. 52 Cdn, Box, Tools U.JPG (209.8 KB, 0 views)
Reply With Quote
  #5  
Old 28-05-22, 18:55
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default

This morning was spent marking out and drilling the three holes in the copper bar, for my Ground Terminal Project. The hardware is all ¼-inch brass, but I went to 17/64-inch for the hole size, just to make assembly a little easier.

Once the holes were in the copper bar, I used the bar as a template for getting the two terminal post holes properly centered on the cover of the electrical box.


David
Attached Images
File Type: jpg Ground Terminal Project 5.JPG (262.6 KB, 0 views)
File Type: jpg Ground Terminal Project 6.JPG (259.2 KB, 0 views)
File Type: jpg Ground Terminal Project 7.JPG (163.7 KB, 0 views)
Reply With Quote
  #6  
Old 28-05-22, 19:08
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default

With the holes drilled in the copper bar now, I could do the assembly of the hardware to the bar.

The centre post will be the connection point for the actual cable to ground. I could not find a round head, slotted, brass screw in the length I wanted but ¼-inch countersunk, slotted were available along with matched brass finishing washers, so I went that route.

The two outer posts will be the pair of terminals on the front of the electrical box, upon final assembly. The sets of three brass hex nuts on these posts, directly behind the copper bar, are merely serving as spacers to allow sufficient clearance for the center post, behind the front cover. Without them, the copper bar would simply bend over the centre post when the hardware for the two terminal posts was run home.

Next step for this assembly will be to give the electrical box a coat of flat white paint and cure.

David
Attached Images
File Type: jpg Ground Terminal Project 8.JPG (230.8 KB, 0 views)
File Type: jpg Ground Terminal Project 9.JPG (233.3 KB, 0 views)
Reply With Quote
  #7  
Old 28-05-22, 19:45
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,621
Default BOXES, Tool, No. 1 WS Cdn No. 52 ZA/CAN 4727

I was able to get a little more work done on this part of the project as well this morning.

After studying the hole in the back wall of the box, where the original hardware was installed, I found it was 11/64-inch in diameter. Just the right fit for a 10-24 screw. The outer hole in the box, partially tucked under the right lower hinge plate, was countersunk. The edge of the hinge plate was bowed outward slightly from the original screw being hammered back out of the hole when removed, but I think I can fix that easily enough down the road.

Test fitting the new bracket and taking s few measurements gave me a probable length of the original screw as being 1-inch. So far so good!

The hole in the bracket for the screw is centred in one end of the bracket. Once again, to give myself a little wiggle room getting the new bracket correctly lined up inside the box, when I install it, I went with a 13/64-inch hole in the bracket.

The new look of the metal on this replica bracket did not match well at all, when test fit directly across from the smaller surviving bracket, so I decided to age it with some zinc plating. This time, however, I did not go through any of the recommended cleaning steps to be done before plating that would normally give one a good even distribution of new zinc on the bracket. I just hooked it up, along with its hardware, and dropped it in the solution for one hour.

Sure enough, the final plating was very patchy and random, and much more like the surviving original. I am quite pleased with it, but have now discovered yet another step may be required. To confirm this possibility, I will need to take another close look inside the box, out in the sunlight. It is going to be raining here again for the next four days!


David
Attached Images
File Type: jpg WS No. 52 Cdn, Box, Tools V.JPG (237.5 KB, 0 views)
File Type: jpg WS No. 52 Cdn, Box, Tools W.JPG (201.0 KB, 0 views)
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Canadian staff car wireless: World War 2 Canadian R103 Receiver Demo Mike K The Wireless Forum 5 24-07-16 15:20
Found: CMP Wireless body project Jim Burrill For Sale Or Wanted 7 05-04-15 00:02
Canadian dehavilland mosquito restoration project David Dunlop WW2 Military History & Equipment 9 10-07-14 00:51
Canadian project David Ellery The Carrier Forum 9 28-04-07 01:36
FOR SALE/TRADE: 1944 CHOREHORSE PROJECT for Signal Corps Wireless Power Unit Project Alain For Sale Or Wanted 1 21-02-07 00:11


All times are GMT +2. The time now is 16:21.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016