For Sale: M8 armoured car bits and pieces for sale

[Big D]

Hi all,

Here is an updated list of M8 and M20 parts I have left over for sale. Rather than list a price, let me know if you are interested in anything and I’ll first work out a freight price and if you are happy with that, then you can make me an offer. I’m not fussed about making money and I’d rather the stuff just gets used. I’m a long way away so I know freight is a factor.

I've attached some photos but can send more if required:

• .50 cal machine gun turret elevator mount
• Brake shoes. NOS and used.
• Map clips. NOS.
• Pedestal light locking pin. May be for H/T but works in M8.
• Brake line covers
• Clutch and brake pedal assembly
• Radio cable tube/conduit
• Voltage regulator. Not working.
• Exhaust header. Needs repair.
• Sponson plates
• Gearshift selector rod.
• 37mm and .30 cal cable mount for seat frame.
• .50 cal gun barrel turret support
• Front engine mount cushions. Rough.
• Front engine mount cushion retainers. Rough.
• Rear engine steel mounts. Rough but repairable
• Oil can bracket. Original
• Throttle salve cylinder mount. Repro.
• Master switch front.
• Throttle reservoir.
• Front axle brake guard.
• Shock absorber mounts.
• Black out light mount. Repro.
• Parking brake and parts
• Hercules Oil pump repair kit
• Fan pulley wheel and adjuster casting
• Fuel pump to carb NOS fittings. Part A-284086.
• Hercules NOS JXD (?) oil pump idler gear
• Pinion seal. NOS. Part number A-283830.
• Carburettor. Needs rebuild.
• Fuel tank enclosure (x2)
• Fuel tank mounts. Originals.
• Ignition coil
• Hercules engine tappet covers
• Distributor shaft end gear
• Distributor. French made. No points, some surface rust inside. Repairable
• Circuit breakers for Generator. NOS
• Primer pump
• Gear shift lever rod pieces. Repro?
• Gear shift lever housings. Both are rough
• Transfer case operating levers
• Transfer case operating lever mounting screws
• Throttle master cylinders. All for rebuild
• Clutch slave cylinders. All for rebuild
• Torque rod ends
• Wheel nuts
• .30 cal belt top guide
• Gun firing cable foot mount. Base is a bit bent but useable.
• 37mm travel lock bracket = TBC
• 37mm rack top
• Hydrovacs and parts
• Drag link. NOS
• Rubber shock absorber mounts
• Brake backing plates. Will require straightening
• Handbrake adjusting pins
• Handbrake shoe
• Axle grease seals
• Brake T connections. Used
• Brake wheel cylinders. Requiring restoration
• Brake wheel cylinder caps. Requiring restoration
• Brake adjustment locking plate
• Brake shoe securing bolts with springs.
• Brake master cylinder. No piston
• Turret mechanism. Mainly complete, plus extra parts
• Steel skirt for turret. 600mm long, for turret repairs
• Protectoscope box holder bolt. Working well
• Latch for hull/hatch visor. Looks a little rough, but works
• Sponson cover. French made. Rough but repairable
• Instrument panel circuit breaker backplate
• Dashboard Silent blocs
• Steel conduit, shunt box to T connection. Bent but should straighten
• Dashboard wiring harnesses. NOS
• Speedometer
• French temperature gauge. Tested and works with sender A297237 = $80
• Oil pressure gauge. NOS. Stewart Warner, Model 405356 = $80

Please PM if interested.

[Big D]

More photos.

[Big D]

And again...

[Big D]

Hi all,

Here is an updated list of M8 and M20 parts I have left over for sale. Rather than list a price, let me know if you are interested in anything and I’ll first work out a freight price and if you are happy with that, then you can make me an offer. I’m not fussed about making money and I’d rather the stuff just gets used. I’m a long way away so I know freight is a factor.

• Flywheel/clutch housing
• Map clips. NOS.
• Countershaft gearset. NOS
• M8 turret seats. Will need work.
• Side locker lids. Good condition.
• Oil can bracket. Original
• Wheel drums. Good condition
• Wheel hubs. Good condition
• .50 cal machine gun turret elevator mount
• Clutch and brake pedal assembly
• Radio cable tube/conduit
• Voltage regulator. Not working.
• Exhaust header. Needs repair.
• Sponson plates
• Gearshift selector rod.
• 37mm and .30 cal cable mount for seat frame.
• .50 cal gun barrel turret support
• Front engine mount cushions. Rough.
• Front engine mount cushion retainers. Rough.
• Rear engine steel mounts. Rough but repairable
• Throttle slave cylinder mount. Repro.
• Master switch front.
• Throttle reservoir.
• Front axle brake guard.
• Shock absorber mounts.
• Black out light mount. Repro.
• Hercules Oil pump repair kit
• Fan pulley wheel and adjuster casting
• Fuel pump to carb NOS fittings. Part A-284086.
• Hercules NOS JXD (?) oil pump idler gear
• Pinion seal. NOS. Part number A-283830.
• Fuel tank enclosure (x2)
• Fuel tank mounts. Originals.
• Ignition coil
• Hercules engine tappet covers
• Distributor shaft end gear
• Distributor. French made. No points, some surface rust inside. Repairable
• Circuit breakers for Generator. NOS
• Primer pump
• Gear shift lever rod pieces. Repro?
• Gear shift lever housings. Both are rough
• Transfer case operating levers
• Transfer case operating lever mounting screws
• Throttle master cylinders. All for rebuild
• Clutch slave cylinders. All for rebuild
• Torque rod ends
• Wheel nuts
• .30 cal belt top guide
• Gun firing cable foot mount. Base is a bit bent but useable.
• 37mm rack top
• Hydrovacs and parts
• Drag link. NOS
• Rubber shock absorber mounts
• Brake backing plates. Will require straightening
• Handbrake adjusting pins
• Handbrake shoe
• Parking brake (handbrake) handle and parts
• Axle grease seals
• Brake shoes. NOS and used.
• Brake line covers
• Brake T connections. Used
• Brake wheel cylinders. Requiring restoration
• Brake wheel cylinder caps. Requiring restoration
• Brake adjustment locking plate
• Brake shoe securing bolts with springs.
• Brake master cylinder. No piston
• Turret traverse mechanism. Mainly complete
• Steel skirt for turret. 600mm long, for turret repairs
• Protectoscope box holder bolt. Working well
• Latch for hull/hatch visor. Looks a little rough, but works
• Sponson lower cover. French made. Rough but repairable
• Sponson lower cover. French made. Painted.
• Instrument panel circuit breaker backplate
• Dashboard Silent blocs
• Steel conduit, shunt box to T connection. Bent but should straighten
• Dashboard wiring harnesses. NOS
• Speedometer
• French temperature gauge. Tested and works with sender A297237
• Oil pressure gauge. NOS. Stewart Warner, Model 405356

I also have Hercules pistons, bearings, valves.

Please PM if interested.