|
|
|
|
#1
18-09-15, 09:25
|
|||
|
|||
Not much happening with my carrier lately , to many jobs around the house I'm still waiting on the motor , did have some luck with the two gallon water cans as per the photos below . I would like some help with info on the front water can for the vickers as to what , the top and bottom holder brackets look like . Some photos show a belt like strap , other have a double rubber pull down quick release type of holder . Dale
  
__________________
1944 GPW and Bantam trailer 
|
|
#2
18-09-15, 10:22
|
|||
|
|||
|
Im looking for the water can strap too. I've got the bottom bracket, I'll take some photos of it tomorrow so you know what you're looking for. I'll finish those vickers ammo box brackets for you next week hopefully.
__________________
1967 Land Rover Plant Repair Vehicle 1941 Matchless G3L 194? Wiles Junior Trailer 1941 Morris Commercial CS8
|
|
#3
18-09-15, 11:23
|
|||
|
|||
|
Thanks Alex . Do the NZ carriers over their , have the same top block welded to the hull with the two 1/4 inch threaded holes as per my photo . Dale
__________________
1944 GPW and Bantam trailer
|
|
#4
18-09-15, 11:49
|
|||
|
|||
|
Yes, my LP2 is exactly the same arrangement as your picture
__________________
1967 Land Rover Plant Repair Vehicle 1941 Matchless G3L 194? Wiles Junior Trailer 1941 Morris Commercial CS8
|
|
#5
30-09-15, 03:08
|
|||
|
|||
|
I'm after some tips on what goes in first before the motor is lifted in ? and any does and don't . Dale
__________________
1944 GPW and Bantam trailer
|
|
#6
30-09-15, 10:18
|
|||
|
|||
|
A couple of pics depicting the bracket and strap.
__________________
1943 Ford GPW Jeep "Follow Me" 1943 MBT trailer 1943 Dodge WC-57 Command Car 1943 Chev C60L Army Cargo Truck 1941 LP2 VR 731 Bren Gun Carrier 3" Mortar Carrying Under restoration: 1940 LP1 Bren Gun Carrier 194? 1 Ton Trl Ben Hur 1942 C15A with sunshine cabin MVPA 31338
|
|
#7
30-09-15, 23:00
|
|||
|
|||
|
Thanks Darrin and Alex for the photos . I just need to see what the top bracket looks like ? Here is a photo below of where i'm at before the motor goes in , with the clutch rod how do the bends look ? does it go behind the exhaust extensions can it be put in after the engine is in ? as it might need test fitting and re bending
__________________
1944 GPW and Bantam trailer
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Vic rail 2225 | colin jones | The Carrier Forum | 109 | 13-07-13 15:15 |
| My GM engine number when was it build?? | 8threcce | The Restoration Forum | 7 | 09-01-12 08:39 |
| Iltis carb re-build kit | servicepub (RIP) | Post-war Military Vehicles | 2 | 15-05-11 22:33 |
| How To Build A 2/5 Sherman Tank | T.J. | The Armour Forum | 1 | 16-01-08 11:17 |
| Pssst... want to build a gun tractor? | Keith Webb | The Softskin Forum | 12 | 16-07-04 00:13 |
Hybrid Mode
