Ford Blitz Restoration/Rebuild

[lynx42]

You are right Tony W. ["That being the case Tony, and at the risk of stating of the obvious, can I suggest you do it yourself! There are no special tools required and everything you need to know is in your trusty Ford manual."]
If you can read a book, you can re-assemble a V8 side-valve.

Here is a photo of 13 year old Joel, My sons stepson, torquing down the head on my Lynx engine. You are never too young to learn.

Regards Rick

1497320_10202470711382789_1398462995_n.jpg

[Tony Wheeler]

Nice photo Rick, great to see youngsters still working on flatheads in 2014! When are you going to buy him his own blitz to restore?

Perhaps we can start a thread on kids restoring CMPs. I think Euan may hold the record at age 12 or something equally ridiculous! Mine was a fair effort with no shed or workbench, but Keith restored his first blitz in the street!

Morrison court.jpg

[Keith Webb]

Well, we got it sort of running, with one front brake working, but at least it was alive again... not bad for a couple of 16 year olds I guess. And the front shell got a coat of paint.

[Private_collector]

Hey, hey, hey! The transfer case is finally back where it belongs.
DSC_0084.jpg DSC_0082.jpg
There was a point in the lifting that I expected the hoist to run out of reach. The boom arm looked to be very high, and I wouldn't have been surprised to need to lift the case in two stages. In the end, it all worked out fine. Once bolted in place, I disconnected the chains to see how much height would have still been available, if needed. I found there was only another 1/2" beyond the height I needed. How's that for lucky.
DSC_0080.jpg
Is this really how the speedo drive sits? That's quite a sharp turn the cable has to make.

DSC_0085.jpg
Now I need to decode how this goes together.
I did take some photos of the way I pulled it apart, but like the maintenence manual, those photos are not as instructive as I would like them to be.

[hrpearce]

Looks good Tony.

[Ryan]

That's just crazy clean. I'd be afraid to drive it.

[Private_collector]

The transfer case shifting assembly is now back on, and with the help of new detent balls & springs, it selects freely. I will remove only the lever, when it comes time to put the cab on the chassis. Where can I buy a new shifter knob? I bought one from Macs some months ago, but it has a thread that is far too small.

I got interested in the wiring harness today, so decided to remove some of the seperate pieces out of the large bag they came in. I wanted to consider installing anything that runs along the chassis. When I removed them all, I found one I wanted, and opened the seal on that particular bag. Got the fright of my life when one of the numbered tags fell off the wire it was wrapped around. I guess over 12 months in a shed which can heat up to the high 40s (celsius) has weakened the gum on the tags! I very carefully reattached that tag, checked all the others on that section, and ever so gently replaced it back into the plastic bag. No further attempt will be made to open any of the bags until I settle on a way to secure those tiny little tags. That could have been disasterous if I had knocked several of the tags off before I discovered the situation. Yikes! Close call.

Gentlemen, I need assistance with some information on two areas.
Firstly, can anyone help me with photos of the part which holds the emergency brake band/shoe to its bracket. I mean the bit on the mid point of the shoe, furtherest away from the opening/closing ends. It can't be much of a mechanism, but I cannot find a diagram or wrawing in the manual. Never had that part, and don't want to try making anything until I know what should be there. Typically, there is no image of this in the manual.
Secondly, I would like to see what the linkage to the PTO looks like. Once again, never had that part, and the info about it in the manual is rudimentary at best. Measurements and closeups of the ends, would be very much appreciated.

Friday I from Mothers house, and brought back a quantity of tools which had belonged to both my Father and my Brother. This morning I arranged them, along with my own tools, into the tool cabinet draws. It was a considerably larger job than I had expected, and was time consuming to say the least. Some of those tools (Dads mainly) are older than I am, some very much older, dating back to the 1930s & 1940s. I hope my Son takes finds them as valuable and worthwhile as I do. Time will tell.

It just occured to me that the rear drive shaft on my junked truck might be an ideal candidate to have shortened to fit the restoration truck. There is always the possibility that it is already too short. Wish I had thought to remove it this morning, but it can wait until Wednesday.