Modern part numbers for CMPs

[Bob Carriere]

Bonjour David

You should check your local brake shops in Kingston.... they may reline your brake shoes cheaper..... and they can turn your drums while your at it.......

a lot of parts are available for the Ford..... but the Chev Master cylinder is rare....... wheel cylinders for the Chev are a stock item in brake shops in Ottawa.

Both Rob Clarke and I have dealt with Ottawa Brake and Clutch with good service.

Bob C.

[Geoff Winnington-Ball (RIP)]

Hi folks... is Tony's list from 01 May '04 the best we have so far? I would urge all of you to post necessary corrections/additions and what I'll do is format this as an HTML chart and post it accordingly. I can't give any of you access to update it, but I can update and repost the list from time to time myself.

Have at it....

[Bob Carriere]

Where is the list...????

Am I having a bad day!!!!!????

BooB

[Geoff Winnington-Ball (RIP)]

Originally Posted by Bob Carriere

Where is the list...????

Am I having a bad day!!!!!????

BooB

Post #8 on this thread, Boobie...

[Bob Carriere]

..... I see the light!!!!

Boob

[sth65pac]

This overhaul kit is available in Australia, and is part number K4X.

It has two gaskets, one o-ring the steel valve, and the outer rubber boot. Diameter of the bore is 1-1/4"

NOTE:
It does not contain the pushrod, inner rod, or the spring.

Ian

[Keith Orpin]

Guys,
I've recently discovered that CR seals have been taken over by SKF, (certainly here in England). Having said that, there is a very good dealer here in England who will still supply seals and bearings, bearing the Chicago Rawhide ancesty, remarked with SKF numbers. If you search the CF part number, subsitute CF for SKF, and the seal/ bearing will appear.
Hope this is of use
Keith

[Bob Carriere]

For wheel brake cylinders......Wagner parts seem impossible to find....

BUT...... Raybestos has them...part number..... WC 4571 Front... $78Cdn
WC 4511 Rear....." "

Ottawa suppliers are no longer keeping them on shelf due to limited demand but they are available in Toronto.

Boob

[Hanno Spoelstra]

Originally Posted by Bob Carriere

WC 4511 Rear....." "

Thanks Bob,

As you know I am looking for the front wheel cylinders. I will ask Alex to chime in for his C8 cylinders.

Re. rear cylinders, I know of the following sources for the 1-1/2" wheel cylinders (original p/n 91T 2192).

1) Mac's Antique Auto Parts: 91T-2261 US$61.95 WHEEL CYLINDER REAR RIGHT OR LEFT 1TON TRUCK ONLY EXCEPT 122 INCH WB 2 1939-1952 (see pic)

2) Dirk Leegwater: these are cylinders from a DAF truck I believe, they have the wrong piston ends but Dirk supplies them with the correct pistons and dust boots. I will have to look up the price for you.

3) Derek bought both his wheel cylinders at NAPA, but I cannot find them on their site.

Originally Posted by sapper740

I can get you all three types of cylinders (rear, front, and master)here in Texas at my local Napa store.

HTH,
Hanno

[Phil Waterman]

Napa has changed their web site again - but I think I found the brake cylinders via their application search instead of part numbers.

Take a look at http://www.napaonline.com/Search/Det...+50028+2028083 see if this looks like it. I'll do some more searching.

Also I'll have my friendly NAPA store see if they are really in the warehouse.

Cheers Phil

[WayneR]

While working on a Chev FAT we have in our Regiment we ended up using the wheel cylinder from the front end of a Canadian MLVW (2.5 Ton). They fit nicely and work great.

Wayne

[Hanno Spoelstra]

Originally Posted by Phil Waterman

Napa has changed their web site again - but I think I found the brake cylinders via their application search instead of part numbers.

Take a look at http://www.napaonline.com/Search/Det...+50028+2028083 see if this looks like it. I'll do some more searching.

Also I'll have my friendly NAPA store see if they are really in the warehouse.

Thanks Phil, I see that if one opts for online shopping all parts can be found on the site. Please note that the link you provided leads to:

Wheel Cylinder - Rear
Part Number: UP 4571
Bore Size : 1 3/8"

But the rear wheel cylinder size for a CMP is 1-1/2". This must be for another non-CMP application.

The link to the correct NAPA front cylinder:

Wheel Cylinder - Front
Product Line: NAPA ULTRA PREMIUM BRAKE PARTS
Part Number: UP 4571
Price: 42.99 Each

Features & Benefits Designed To Match O.E. Fit, Form & Function.; High Quality Rubber, Smooth Bore Finishes & Properly Threaded Outlet Ports Ensure Trouble-Free Operation.; Compatible w/ DOT Approved Silicone- Or Glycol-Based Brake Fluids.

Attributes Bore Size : 1 3/8"
Wheel Cylinder Line Thread Size : 1/2" - 20

Hanno

[Hanno Spoelstra]

Link to the correct NAPA rear cylinder:

Wheel Cylinder - Rear
Product Line: NAPA ULTRA PREMIUM BRAKE PARTS
Part Number: UP 4511
Price: 77.49 Each

Features & Benefits Designed To Match O.E. Fit, Form & Function.; High Quality Rubber, Smooth Bore Finishes & Properly Threaded Outlet Ports Ensure Trouble-Free Operation.; Compatible w/ DOT Approved Silicone- Or Glycol-Based Brake Fluids.

Attributes Bore Size : 1 1/2"
Wheel Cylinder Line Thread Size : 1/2" - 20