MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Carrier Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 01-05-22, 09:44
carrierbarry carrierbarry is offline
Barry
 
Join Date: Apr 2007
Location: Watford, London
Posts: 216
Default Carrier smoke

Yes smooth idle, but lot of smoke.
Took it for a drive yesterday, started on the button. Lot of smoke before and after a mile drive. Seem to run better with a little bit of choke. No obvious loss of power. Fuel is about two years old, but lots and smells ok. Going to give her an oil change and clean filter. What’s the best oil and where to buy in UK.
Reply With Quote
  #2  
Old 01-05-22, 13:17
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,541
Default

Cummins Blue diesel oil because the diesel oil has more zinc that most petrol engine oils. The diesel oil is high detergent and might help to un gum your oil rings (which sounds like the problem to me?)
If not then a mono 30 grade oil high in zinc (important) The zinc has been largely removed from petrol engine oil for "enviromental" reasons.
Do some research to bolster your choice.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #3  
Old 01-05-22, 14:15
Richard Farrant's Avatar
Richard Farrant Richard Farrant is offline
Registered User
 
Join Date: Feb 2003
Location: Kent, England
Posts: 3,641
Default

Quote:
Originally Posted by Lynn Eades View Post
Cummins Blue diesel oil because the diesel oil has more zinc that most petrol engine oils. The diesel oil is high detergent and might help to un gum your oil rings (which sounds like the problem to me?)
If not then a mono 30 grade oil high in zinc (important) The zinc has been largely removed from petrol engine oil for "enviromental" reasons.
Do some research to bolster your choice.
I would not recommend using a high detergent diesel oil in an engine of this age which is probably been running on the old style monograde with little or no detergent. You may think it will un-gum the rings, but worse than that it will release all the sediments in lower part of the engine and put them in circulating and hence cause damage to the bearings. I have been 55 years in the trade working on engines and would never use a high detergent oil in and old engine of unknown history. Just changing the oil will not get rid of the sediment.
If it had just been overhauled and clean inside, then a different matter.
__________________
Richard

1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2
Member of MVT, IMPS, MVG of NSW, KVE and AMVCS
KVE President & KVE News Editor
Reply With Quote
  #4  
Old 01-05-22, 18:44
carrierbarry carrierbarry is offline
Barry
 
Join Date: Apr 2007
Location: Watford, London
Posts: 216
Default

Both good answers, thanks for the help. What would you recommend Richard. New plugs, clean air filter, oil change ,,clean oil filter. And some fresh fuel.
I’m sure it’s just we’re she’s been sitting idle though the winter.
What grade of oil would you use?
Reply With Quote
  #5  
Old 01-05-22, 19:06
Richard Farrant's Avatar
Richard Farrant Richard Farrant is offline
Registered User
 
Join Date: Feb 2003
Location: Kent, England
Posts: 3,641
Default

Quote:
Originally Posted by carrierbarry View Post
Both good answers, thanks for the help. What would you recommend Richard. New plugs, clean air filter, oil change ,,clean oil filter. And some fresh fuel.
I’m sure it’s just we’re she’s been sitting idle though the winter.
What grade of oil would you use?
Hi Barry
I wouLd run the engine up and get it hot, then drain the oil. Smell the oil to see if there is any hint of petrol. If so there may be petrol leaking through the fuel pump diaphragm and into the oil and thinning it out which could be a cause of the smoke. The specified oil for Carriers by British army was SAE 30 and I would use one of the Classic 30 oils which you often find stocked in local motor factors.
I did suggest in an earlier post to take the plugs out one at a time to see if any particular ones were oily as that could indicate a problem withiN that cylinder.
__________________
Richard

1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2
Member of MVT, IMPS, MVG of NSW, KVE and AMVCS
KVE President & KVE News Editor
Reply With Quote
  #6  
Old 01-05-22, 20:03
Ron Pier's Avatar
Ron Pier Ron Pier is offline
Registered User
 
Join Date: Apr 2009
Location: Poole. UK
Posts: 1,273
Default

I concur with Richard regarding the detergent oil. Ron
Reply With Quote
  #7  
Old 01-05-22, 21:32
carrierbarry carrierbarry is offline
Barry
 
Join Date: Apr 2007
Location: Watford, London
Posts: 216
Default

I checked plugs, no oil. But running a bit rich.
Took leads off one at a time ,each time engine missed.

Think I’ll change oil.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
help with engine swap to 8BA engine Jason Linders The Restoration Forum 72 31-03-14 12:46
DIFFERENCE BETWEEN CHEVY ENGINE 216 and CHEVY ENGINE 234 serge The Restoration Forum 2 15-03-14 06:55
M38A1 Cdn2 engine vers American engine Retsarge Post-war Military Vehicles 5 22-05-10 01:42
English Smoking Ban Geoff Winnington-Ball (RIP) The Sergeants' Mess 27 08-01-08 10:59
Wanted: engine parts '40 331cu in T124 Dodge VK engine dodgenut For Sale Or Wanted 0 21-06-07 17:25


All times are GMT +2. The time now is 20:17.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016