|
|
|
|
#1
16-04-12, 06:27
|
|||
|
|||
My first CDN2 washer and button look like this:
  The new CDN2 washer squirter looks like this (shown to the left of the hood hinge in the black area), has a foot mounted rubber pump on the extreme left drivers side foot area and has a white coloured round plastic bottle near the solid state turn signal box:  The new CDN2 windshield markings: 
Last edited by rick25; 19-04-12 at 05:36. 
|
|
#2
17-04-12, 01:41
|
||||
|
||||
|
Congratulations on a nice find. My brother lives on that island and it isn't very big. I will have to give him a slap and tell him to keep his eyes open.
Cheers, Barry
__________________
Every twenty minute job is one broken bolt away from a three day ordeal.
|
|
#3
17-04-12, 02:24
|
|||
|
|||
|
Got home from work today and removed the dipstick to find a crankcase full of decent looking and smelling oil so i decided to pull the plugs and shoot some liquid wrench down into the cylinders and, not having really any patience, I gave the fan pulley a spin. Great news for me as the crank pulley spun freely. I also noted that while my parts cdn2 has a military junior oil filter, the new jeep has a cuno. Was there any deciding factor for this or was it random at the rebuild factory?
|
|
#4
17-04-12, 03:37
|
||||
|
||||
|
How did the plugs look?
I would maybe take the dist cap off and have a look and see whats up inside. I think the carb would probably give you some trouble being all dried out but who knows... At the very least, if I were to try running it, I would definately disconnect the fuel line at the fuel pump and plumb in a gas can to start it, that way no old or bad fuel going through the carb. You never know, it may start right up. I bought a M37 a few years back that had been sitting for many years since being surped in the early 1980s. The owner couldn't get it to run at all and I bought it for a song. It took me about 5 minutes to figure out what was wrong with it. I pulled the cap and it and the rotor were baffed beyond belief. A new cap and rotor, a fresh gas can and a charged pair of batteries and she fired right up. Granted, it ran like crap because of all the old crap in the carb, cylinders etc but that was fixed in about 15 minutes running on high idle with the throttle lock pulled on and a quart of transmission fluid applied generously down the intake. She smoked like hell but once that tranny fluid did its job, the longer it ran the better it ran. I never did pull the heads or anything, I did a basic tuneup with plugs, wires cap and rotor and for good measure rebuilt the carb. It only got beter after that.
__________________
3RD Echelon Wksp 1968 M274A5 Mule Baifield USMC 1966 M274A2 Mule BMY USMC 1966 M274A2 Mule BMY USMC 1958 M274 Mule Willys US Army 1970 M38A1 CDN3 70-08715 1 CSR 1943 Converto Airborne Trailer 1983 M1009 CUCV 1957 Triumph TRW 500cc RT-524, PRC-77s, and trucks and stuff and more stuff and and....... OMVA, MVPA, G503, Steel Soldiers
|
|
#5
17-04-12, 05:28
|
|||
|
|||
|
Jr military was the standard in the 60s and 70s. The cuno was a throwback from the 50s. Surprising that would be on a late model jeep like that, but there was some interchange of early engines into later trucks. How many belts are your pulleys made for? Two were the early engines, 3 were the later engines.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
