#1
|
|||
|
|||
C8a Hup
Hello all.
I am in need of photos showing the back seat in a C8A Personel! Have someone wondering how it was fastened to the floor. Any photos or drawings would be greate! Will ask permition to show photos of a very butifull personell, and be back. Rolf |
#2
|
|||
|
|||
HUP Middle or Rear Most Seats
Rolf - Not sure which seats you mean the middle bench seat with built in tool storage or the rear most seats which are the same as the front seats. Attached is a photo of my middle seat, which is bolted to the floor with 1/4 inch bolts there are captive nuts under the floor. Originally the seats were held down by wing-nut bolt shown in primer paint these were retained with a short chain. The one shown is the only one that survived on my truck I have used grade 8 bolts as replacements.
__________________
Phil Waterman `41 C60L Pattern 12 `42 C60S Radio Pattern 13 `45 HUP http://canadianmilitarypattern.com/ New e-mail Philip@canadianmilitarypattern.com |
#3
|
|||
|
|||
middle bench
and not the rearmost ones.
But thanks Phil. I guess it is helping Frantisek, which is a new member on this forum. I guess he will ask you more questions, and hopefully he will present some photos of a very nice C8A 1C11... Rolf |
#4
|
||||
|
||||
That's a useful pic Phil. I, too, have been wondering what the rear bench seat for the HUP looks like - is that the one with the two-way back rest to fit in the tubes?
Do you have the rear-corner jumps seats as well? I don't know what the look likeither. I had a look at a HUP a few weeks back that had a bench seat in the right location, but it was some latter-day car seat, and the installation fittings did not look original, but cobbled up - is there some sort of tubular fitting facing forward in the centre of the floor? I will review my snaps to compare later.
__________________
Member: Prairie Command, Ex-Military Land Rover Association 2110, MVPA 29055 ’45 Chevrolet C8A CMP HUP “Staff Car ”, ’82 Land Rover Series III, 109" ex-MoD, ’80 Honda CX500D, ’48 Ferguson TE20 |
#5
|
|||
|
|||
Seat C8A 1C11
Hello!
i´m František, the "new member". I´m helping my friend, who bought one C8A 1C11 from my father 20 years ago ) thank you very much for the foto, but I need the foto of thi middle sead in 1C11 Pers 3, it is not the same. We have the seat but not the adapter, that is on the base. The seat is moveable, so there has to be somethig... I´ll try to give here photos... |
#6
|
|||
|
|||
me
I´m sorry, I wanted to post here a photo, but I made a new thread... plaese look at it...sorry František Nachlinger
|
#7
|
|||
|
|||
another view
|
#8
|
|||
|
|||
the 1C11 seat
|
#9
|
||||
|
||||
The 1C11 was the staff car and the interior was fitted entirely different to the other HUPs. I don't have any pics but there was usually a folding table arrangement with the double seat.
|
#10
|
||||
|
||||
MORE PHOTOS PLEASE!!!
Wow! Nice HUP. Could you please post more shots of the folding desk and perhaps more shots of the interior? They would be much appreciated!
__________________
RHC Why is it that when you have the $$, you don't have the time, and when you have the time you don't have the $$? |
#11
|
|||
|
|||
more... Please, do you know any gallery where I could get more pictures? ( cca 50), each has cca. 700 kb. thank you.
FN |
#12
|
||||
|
||||
Frantisek - as I am noting in my email to you, your photos are so far the best I have yet to see of a 1C11 interior.
Here is a detail shot of a non-original seat installation (not my C8A), and I am wondering if that central fitting might be original or an add-on.
__________________
Member: Prairie Command, Ex-Military Land Rover Association 2110, MVPA 29055 ’45 Chevrolet C8A CMP HUP “Staff Car ”, ’82 Land Rover Series III, 109" ex-MoD, ’80 Honda CX500D, ’48 Ferguson TE20 |
#13
|
|||
|
|||
Photos
Hi Friends!
This wednesday I go to Ivan to make some photos, so if anybody wants any photo (or some dimensions) of any part of that 1C11 write here or mail me to frnach@atlas.cz and I´ll try to make it for you! |
|
|