|
#1
|
||||
|
||||
Thread - Pilot Drill Charts
Hello All,
Just wondering if there is some form of "Quick Reference Guide" or chart available; online or elsewhere, which identifies what size thread or drill should be used when working with different material. For example, when drilling a pilot hole for a 6 G screw into wood what size should the pilot drill be? Once upon a time this information used to be printed on the screw's packaging. This information is getting rarer to find each time I go into a hardware store. Also, is there some form of table that shows if a piece of steel rod of a certain dimension needs to be threaded - what size thread is the most suitable for the application? Similarly, a chart that shows what size tap to use to cut a thread into a specific drill diameter? Any assistance would be greatly appreciated. Kind regards Lionel
__________________
1940 Chevrolet MCP with Holden Built Cab (30 CWT). 1935 REO Speed Wagon. 1963 Series 2A Army Ambulance ARN 112-211 Series III ex-Military Land Rovers x 2 |
#3
|
|||
|
|||
Lionelgee, next time you go to your engineers supplies place for a bearing or a can of CRC ask for a "tap drill chart" Sutton or who ever does drills, will probably produce one.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
#4
|
|||
|
|||
Quote:
With reference to wood screws in softwoods, it is not that critical to just eyeball a drill size the same or slightly larger than the minor diameter of the screw (diameter at the bottom of the threads). With hardwoods, use a larger drill with a diameter up to half the depth of the threads. I have broken off woodscrews in hardwood by using too small a pilot hole. With a set of fractional and metric drills you will always find a good size. If you find the screw very tight going in just back it out and run the next larger size drill down the pilot hole. The diameter of holes for tapping and diameter of rods for threading are always determined for the specific tap or die and not the other way round. There is some tolerance with threading a rod slightly oversize, but little or no tolerance for a hole undersize for tapping. A broken tap will likely ensue. Studying a tapping and drilling chart will show you what is possible. Hope this is of some help. Cheers,
__________________
F15-A 1942 Battery Staff Jacques Reed Last edited by Jacques Reed; 23-08-19 at 00:17. |
#5
|
|||
|
|||
Jacques, one that I have wanted to do in the last few days was 5/16 UNF.
It requires a 6.8mm or 6.9mm hole. Not found in the standard metric drill set (0.5mm steps) and nothing close in imperial. So there are a few sizes that really could do with their own special purpose drill bits. On the tight screw thing, (please stay on topic) I was told (years ago) to run the threaded end through your hair. (does not apply to everyone) I have found that it does make a difference.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
#6
|
|||
|
|||
Letter and number drill sizes
Hi Lynn,
Just checked my Machinery's Handbook and see what you mean. The attached shows a 5/16 UNF tap requiring a Letter I drill: 0.272" Not the kind of thing you would get at the local hardware store. Number and letter size drills derived from American and British wire gauge sizes and are still sometimes used in American industry. 17/64" might be too small and risk tap breakage. 9/32" would not leave a lot of thread. A 7.0 mm drill might work. Converting 7.0 mm to inches is 0.2756" which is only 0.0036" larger, about the thickness of printer paper, and might suffice. I inherited the attached partial set of number drills. Sets like that or letter drill sets may turn up at swap meets. Rubbing a wood screw on a block of soap also aids screwing it in. Oops! off again. Cheers,
__________________
F15-A 1942 Battery Staff Jacques Reed Last edited by Jacques Reed; 23-08-19 at 08:52. |
#7
|
|||
|
|||
Jacques, I used the 17/64 drill and tried a tap which didn't feel good, so tried another which felt somewhat better. I tapped 8 holes. It worked but will plan to buy a 6.8mm bit at some point in the future.
In N.Z. Patience and Nicholson make drill bits. I think they are an off shoot of the Australian drill maker (lost the name for the moment) anyhow the put out some very good charts: one a tap-drill chart and the other a drill selection chart. together very useful. There are some horrible and useless drill bits on the market these days.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
#8
|
||||
|
||||
Hello All,
Thank you for all the replies and suggestions. The last time I saw a table of the different sizes for threads and pilot holes was in the back of my high school Year 10 Metal Work Textbook. That was quite some time ago..... It was the year where Love is Like Oxygen - by The Sweet and Lay Down Sally by Eric Clapton was in the Australian Top 100 Songs Kind regards Lionel
__________________
1940 Chevrolet MCP with Holden Built Cab (30 CWT). 1935 REO Speed Wagon. 1963 Series 2A Army Ambulance ARN 112-211 Series III ex-Military Land Rovers x 2 Last edited by Lionelgee; 23-08-19 at 11:47. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
For Sale: 4 wall charts to mount WS19 Set in a M 24 1944 date | Dean (Ajax) | For Sale Or Wanted | 0 | 28-08-12 14:38 |
A different kind of Gun Drill! | Gunner | The Gun Park | 1 | 10-05-12 01:30 |
FS: NOS M4 High Speed Tractor Maintenance & Service Charts | Steve Greenberg | For Sale Or Wanted | 0 | 13-11-11 06:31 |
Axe Drill | jeff davis | WW2 Military History & Equipment | 4 | 15-04-07 15:52 |
Bofors Gun Drill | Bob Moseley (RIP) | WW2 Military History & Equipment | 6 | 27-06-05 17:00 |