CMP front wheel bearing shims

[Jordan Baker]

Would anyone have a sample of any of these shims. Trying to determine outside and inside dimensions. They are for the front wheel bearings

[rob love]

Not sure I have any loose right now, but they only need to be the diameter of the spacer, or a similar diameter to the center part of the bearing.

[Tony Smith]

The Shims are used in conjunction with a cast steel "Teacup" shaped spacer that sits between the inner bearing cone and the outer bearing cone. Only one side of the Teacup will use the shims, to obtain preload on the wheel bearings. The shims will be the same dimension (I.D./O.D.) of either the large or small end of the teacup, and also the corresponding face of the wheel bearing cone.

Unfortunately, I don't have a front hub disassembled at the moment to take pics or measurements. There should be a pic in the Parts List to show the arrangement.

[John Sek]

Originally Posted by Tony Smith

The Shims are used in conjunction with a cast steel "Teacup" shaped spacer that sits between the inner bearing cone and the outer bearing cone. Only one side of the Teacup will use the shims, to obtain preload on the wheel bearings. The shims will be the same dimension (I.D./O.D.) of either the large or small end of the teacup, and also the corresponding face of the wheel bearing cone.

Unfortunately, I don't have a front hub disassembled at the moment to take pics or measurements. There should be a pic in the Parts List to show the arrangement.

Hi Tony,

I believe Jordan's query was on my behalf, I am not one for using the forum, even though I should do so more. I just replaced the outer bearing on my C15a driver side wheel, but figure that I need to install shims to make sure the bearings are properly adjusted (certainly shows the shims in the exploded view of the parts manual and discusses it in the maintenance manual). Lost the original I had when I first worked on this several years ago. Bearing recently failed, so figured the failure may have been the result of not using any shim when I reassembled it. I sort of figured that I could use the teacup spacer to determine the I.D./O.D. size but was concern if the resulting shim should be exactly the same size or slightly smaller. When you dry fit the spacer up against the bearing cone its a very narrow seat just short of touching the roller assembly. If I was going to order some made or see what may be currently available wanted to be absolutely correct on the dimensioning.

If anyone has a spare shim that I could take measurements that would solve the problem.

cheers,

John

[Jacques Reed]

Hi John,

I posted this on MLU Forum on their FB page this morning. Replying to Jordan.

From my F-15A Parts List Ford and GM are the same.

Here is one of mine: 3.00" OD, 2.75" ID

Hope this helps.

Cheers

[Jordan Baker]

Thanks all. My original question was on behalf of John.

[Tony Smith]

Originally Posted by Jacques Reed

Hi John,

I posted this on MLU Forum on their FB page this morning. Replying to Jordan.

Hope this helps.

Cheers

WHAT!! A secret "Shadow" MLU is out there?

[Hanno Spoelstra]

Originally Posted by Tony Smith

WHAT!! A secret "Shadow" MLU is out there?

Yes, read about the “why” here: http://www.mapleleafup.net/forums/sh...ad.php?t=24991

Keith Webb set up a CMP Facebook page long before MLU-FB, there’s also an Australian group on Blitzes and a myriad of other groups on all sorts of related subjects.

[Tony Smith]

Originally Posted by John Sek

If I was going to order some made or see what may be currently available wanted to be absolutely correct on the dimensioning.

If anyone has a spare shim that I could take measurements that would solve the problem.

cheers,

John

I suppose you would want to know the thickness of shim that you require before buying, but you wouldn't be able to get pre-load figures without having an assortment on hand. Usually a good starting point is the shim thickness that was used prior to replacing the bearing.

Post number #2 in this thread might be of assistance: http://www.mapleleafup.net/forums/sh...ad.php?t=25583