#1
|
||||
|
||||
Tight distributor
Hi All
I am helping to tune an L134 engine in a Willys Jeep. We came to a halt after loosening the nuts and trying to turn the distributor. However the distributor is well and trully stuck and will not move, we tried pulling it out and again no movement. I did not want to put any force on it, so I decided to put it you who have the knowledge and experience. Can anyone suggest how I can get the distributor to move or how I can pull it out. I find it confusing as the vehicle is regularly used so it should not be rusted up like a long time unused engine sitting in a field. Or should I just leave it alone, like the old saying, " If it aint broke, don't fix it ". Cheers Tony
__________________
Anthony (Tony) VAN RHODA. Strathalbyn. South Australia |
#2
|
||||
|
||||
Distributer removel
Tony,
I have been there and was not impressed, There is no easy way to remove it, Start by spraying a lube around the base of the distributerand pray that after a few days of this with some pressure left to right it comes. If it dont only othe way is to remove the oil pump and get some hard wood dowel and insert it up into the oil pump housing hole and start taping untill it comes loose, this was the only way i could do it also. The engine that i did it to was rebuilt a year before but was put away for winter and thats all it took. When you get it out coat the base of the Distributer with grease, you wont have a problem again. Jason
__________________
42 Slat grill 43 Ford gpw 44 C15A Wire 5 |
#3
|
|||
|
|||
Jo
Try using an oil filter strap (with a lever) on it. Put the strap low on the body, and be careful not to distort the housing.
If the engine runs, let it warm up and cool down a couple of times, after it has been soaked with penetrating oil, for a day or two. The jeep dizzy has a small dog on the end. It can only be the distributor body stuck in the block bore. Good luck!
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
#4
|
||||
|
||||
Hi Jason and Lynn
Thanks guys for coming back to me with a solution. I will ensure we follow it to the letter. We will spray some good old WD40 around the base as suggested and I will also get a oil filter strap. Thanks again, MLU members have done it again. Appreciated. Cheers Tony
__________________
Anthony (Tony) VAN RHODA. Strathalbyn. South Australia |
#5
|
|||
|
|||
Try the "ED's Red" mixture. 50% acetone mixed with 50% ATF fluid.
|
#6
|
||||
|
||||
Willtry
Quote:
Thanks for the tip. I need all the advice I can get. Cheers Tony
__________________
Anthony (Tony) VAN RHODA. Strathalbyn. South Australia |
#7
|
|||
|
|||
Common situation on these engines.
Use lots of croil, oil filter strap and PATIENCE!! I worked with mine for over two weeks. Sprayed on, put some force into the strap, gentle tapping with a plastic hammer on the dizzy to times every day. Finaly it came loose. No rust, just old dirt, grease and oil binding it. Try to no destroy the dizzy dataplate if it is present.... It will come loose...just dont use too much force. Good luck Svenn |
#8
|
|||
|
|||
tigh distributer
Acetone and ATF is the answer .I couldn't get the handle bars off of my WLC but two days later with this combo and I could take the nut off with hand pliers .The best thing I have used yet .
__________________
George is hooked on OD 5 window DT969 8 ton Fruehauf trailer M2A1Halftrack ,CMP #11 F15A1 #13 F15A1 RAF Fordson Tractor, 42 WLC HD No.2MK11 CT267514 center CB24713 bottom hull25701 ,No.2 MK2 parts MK1 10128 ,(2) MK1 ,Parts Hull9305 .Hull 10407 Hull plate # 7250 all have walk plate on back steps 1917 Patent modle amphibious army tank |
#9
|
||||
|
||||
Great gadget
Svenn - Georgene
Thanks guys, I am happy with all the MLU support and good advice. I am sure we will now win this little stubborn battle. Svenn that is a great little gadget, I haven't seen that before, I am taking a photo of it to the hardware store and see if they can get me one. If not a nice little project to make one. Cheers Tony
__________________
Anthony (Tony) VAN RHODA. Strathalbyn. South Australia |
#10
|
|||
|
|||
oil filter wrench
Here it is
http://www.globalsources.com/gsol/I/...1032194602.htm If i should do it again, I will wrap several layers of ducktape around the dizzy first. The strap may othervise make some marks in the dizzy. svenn |
#12
|
|||
|
|||
most car / garage tool dealers have this one in norway I guess that it is common other places as well
Heres it at ebay: http://www.ebay.com/itm/Oil-Filter-W...b765aa&vxp=mtr Svenn |
#13
|
||||
|
||||
Thank you
Quote:
Thanks mate, I will get onto it right away. Cheers Tony
__________________
Anthony (Tony) VAN RHODA. Strathalbyn. South Australia |
#14
|
|||
|
|||
If you go to the parts store at Handorf, he used to keep them.
I bought one for my lady to undue the lids off bottles. Regards Col
__________________
Vietnam Vet and proud of it. |
|
|