MLU FORUM  

Go Back   MLU FORUM > BUY, TRADE or SELL > For Sale Or Wanted

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 24-08-22, 22:46
Marc Montgomery's Avatar
Marc Montgomery Marc Montgomery is offline
aut viam inveniam aut fac
 
Join Date: Feb 2003
Location: Canada
Posts: 606
Default Unstucker kit

NOS unstucker kit, complete as supplied.

Can deliver to Montreal Cornwall along the 401, Kingston hwy 15/401

The orig handbook is there as well but only in spirit.

Asking $400=== OBO

contact convoymagazine AT yahoo.com
Attached Thumbnails
FOR SALE 2021 UNSTIUCK 1000.jpg  
__________________
I see you stand like greyhounds in the slips,
Straining upon the start. The game's afoot!

Last edited by Marc Montgomery; 31-10-22 at 00:38.
Reply With Quote
  #2  
Old 25-08-22, 05:57
Jon Skagfeld's Avatar
Jon Skagfeld Jon Skagfeld is offline
M38A1 CDN3
 
Join Date: Feb 2003
Location: Owen Sound ON
Posts: 2,190
Default

Is that for the 5 quarter Ton Chev
__________________
PRONTO SENDS
Reply With Quote
  #3  
Old 25-08-22, 16:28
Marc Montgomery's Avatar
Marc Montgomery Marc Montgomery is offline
aut viam inveniam aut fac
 
Join Date: Feb 2003
Location: Canada
Posts: 606
Default

HI Jon
bought as an Iltis attachment, but never used as I never took the jeep offroad . strictly a fair weather, fair road pleasure vehicle. In fact, the kit has only been out of the bag a couple of times, when first bought and for photo.


might work for a Mutt? Don't know about other vehicles.

Rob Love would know,
Maybe Stuart.
__________________
I see you stand like greyhounds in the slips,
Straining upon the start. The game's afoot!
Reply With Quote
  #4  
Old 25-08-22, 17:08
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

It really comes down to what is there for the wheel adapters and wheel nuts. Show a photo of the two wheel adapter plates and we will know. The photo shown they almost look like 5/4 ton adapters, which are much deeper than the Iltis or M151A2.

The drums, rope, T wrench and equalizer were the same for all the vehicles.
Reply With Quote
  #5  
Old 26-08-22, 06:01
super dave super dave is offline
Dave Good
 
Join Date: Dec 2003
Location: Onoway, Alberta, Canada
Posts: 683
Default

Here is a picture of the 2 different types of studs for the plates, the long ones I believe are for the Mutts and the short ones are for the 5/4. The adapter plate is also for the 5/4 where the flat plates fit the Mutts and the Iltis and the iltis also has different studs as well.
Attached Thumbnails
20190614_205918.jpg   20190618_210732.jpg   20190614_205907.jpg  
Reply With Quote
  #6  
Old 26-08-22, 13:48
maple_leaf_eh maple_leaf_eh is offline
Terry Warner
 
Join Date: Mar 2004
Location: Shouting at clouds
Posts: 3,081
Default at the risk of derailing

Marc, good luck but I won't be buying.

A hundred and fifty years ago, the M38A1s had a percentage of With Winch models. In the Reserves these were seldom used. We were kids and although there was a Performance Check in our training to learn how to run the winch, most of the instructors had little or no experience running them. Towing was the preferred way of getting unstuck, and every available 15' steel cable with a triangular or oval end was distributed across the recce troop. I remember using them once.

There were no M151A2s or Iltis With Winch. The Unstucker kit was a staff idea to keep single vehicles mobile. Good idea, but IMHO not a success. The kit almost always stayed in one of the bins - because it was on the checklist. In Bosnia '02-'03 the HQ where I was posted had a number of Itli' and I clearly remember having to stand out in the rain learning about chaining up. The driver had to clamp the links shut against resistance, and then rubber bungee the whole thing snug. Staying on the road or at least just skating on it, was probably the lesser of two evils.
Attached Thumbnails
Iltis 86476.JPG  
__________________
Terry Warner

- 74-????? M151A2
- 70-08876 M38A1
- 53-71233 M100CDN trailer

Beware! The Green Disease walks among us!
Reply With Quote
  #7  
Old 26-08-22, 14:07
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

I concur with Dave's assessment of the parts. The M151 did not use a tapered wheel nut...the ones he shows are correct for that application. The long tapered ones are for the 5/4 ton.



As a mechanic, we did not particularly like the unstucker plates. It meant we needed to use 2 or 3 sockets to remove a wheel. And the tiny cross wrench that came with the kit was too short to work on the wheel nuts. We would remove them, replace the long wheelnuts with normal ones, and put the kits in the back of the truck.



Re Terry's assessment of operators and winches, I recall operators calling us when they got stuck despite there being several winches on the vehicles at the location of the casualty. Wisely, the operators knew they were entering dangerous territory once you hooked up the winch cable and did not have sufficient experience. Not everything is a 1:1 straight pull.

Last edited by rob love; 16-09-22 at 17:18.
Reply With Quote
  #8  
Old 26-08-22, 15:49
Marc Montgomery's Avatar
Marc Montgomery Marc Montgomery is offline
aut viam inveniam aut fac
 
Join Date: Feb 2003
Location: Canada
Posts: 606
Default

Great photos showing differences..helpful to many I think so thanks !
Also great stories which explains perhaps why this was /is an NOS item never used.

I bought it never intending to actually use it, but as an accessory for display, (but again never did)
Still, it obviously could be of use for someone going off road, or for display...
I know some hate the Iltis, but i've really enjoyed driving it around in the nice summer weather, and I like the ability to go highway speed if needed. (seldom in my case although i did drive the 401 with no problem at all in the couple hundred km from Montreal to Gananoque, where it spends its life now.

It's really quite cool to drive something so incredibly basic (as are all jeeps) compared to the pushbutton, computerised, automatic, touch screen even self driving things of today.
You really do have to know how to drive these old vehicles.
When I see some of the driving schools today (with EVs no less) and how they seem to be teaching new drivers...sheesh.


PS are those 2 antennas on the front of the Iltis? One i guess HF? the other?
__________________
I see you stand like greyhounds in the slips,
Straining upon the start. The game's afoot!

Last edited by Marc Montgomery; 26-08-22 at 15:56.
Reply With Quote
  #9  
Old 16-09-22, 15:06
Marc Montgomery's Avatar
Marc Montgomery Marc Montgomery is offline
aut viam inveniam aut fac
 
Join Date: Feb 2003
Location: Canada
Posts: 606
Default

I will take a photo of the studs and add it shortly.
Attached Thumbnails
FOR SALE 2022 UNSTUCK BITS.jpg  
__________________
I see you stand like greyhounds in the slips,
Straining upon the start. The game's afoot!

Last edited by Marc Montgomery; 22-09-22 at 17:31.
Reply With Quote
  #10  
Old 28-10-22, 16:47
Marc Montgomery's Avatar
Marc Montgomery Marc Montgomery is offline
aut viam inveniam aut fac
 
Join Date: Feb 2003
Location: Canada
Posts: 606
Default

Accepting offers.
Can deliver along 401 from Mtl to Hwy 15 at Kingston
__________________
I see you stand like greyhounds in the slips,
Straining upon the start. The game's afoot!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale: ILTIS Unstucker Marc Montgomery For Sale Or Wanted 0 12-09-21 01:33
Wanted: "Unstucker" Flanges Scott Bentley For Sale Or Wanted 14 18-07-13 22:46
WTB: M101CDN2 Trailer, Iltis Wheels, Radiator Shield/Unstucker Kit T. Alcorn For Sale Or Wanted 0 11-01-10 21:57
WTB: 5/4 ton unstucker wheel nuts rob love For Sale Or Wanted 7 02-08-08 16:58
Iltis Unstucker. peter simundson For Sale Or Wanted 2 03-03-08 03:05


All times are GMT +2. The time now is 23:51.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016