MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Restoration Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 13-02-07, 11:42
maverick maverick is offline
Alan Bumford
 
Join Date: Oct 2006
Location: Swindon Wilts England
Posts: 93
Default Siezed Ford Engine

There seems to be a lot of different ideas about the best way to go about this. All theorys will be greatly received !
Reply With Quote
  #2  
Old 13-02-07, 12:16
Geoff Winnington-Ball (RIP)'s Avatar
Geoff Winnington-Ball (RIP) Geoff Winnington-Ball (RIP) is offline
former OC MLU, AKA 'Jif' - sadly no longer with us
 
Join Date: Feb 2003
Location: Toronto, Ontario, Canada
Posts: 5,400
Default Re: Siezed Ford Engine

Quote:
Originally posted by maverick
There seems to be a lot of different ideas about the best way to go about this. All theorys will be greatly received !
Pull all the plugs, fill the cylinders with penetrating oil, then put the plugs back in. Let it sit for the day. When the time comes, drain the sump oil and replace it with 30wt which has been prewarmed. Pull the plugs again, then try to hand-crank the engine to loosen it up. Yes, it will make a mess. You can clean that up.

THEN.... strip the engine and have the block boiled and magnafluxed... flatheads are notorious for cracks in their blocks. These have to be fixed or a new block found. Old-time engine-builders can be invaluable here. In any case, new pistons and rings should be invested in, never mind a professional valve job and having the crankshaft inspected and turned and having the bearings changed. You get the idea.
__________________
SUNRAY SENDS AND ENDS
:remember :support
Reply With Quote
  #3  
Old 13-02-07, 12:23
cletrac (RIP)'s Avatar
cletrac (RIP) cletrac (RIP) is offline
David Pope
 
Join Date: Jul 2003
Location: Eston, Sask, Canada
Posts: 2,251
Default

It all depends on how badly it's seized. With a flathead it's easy to take the heads off and hone out the visible rust. Then start with the diesel fuel in the cylinders treatment for a week or so. The best way to get a lot of rotating pressure is to pick a cylinder that's on the top half of its stroke that has the valves closed and screw a high pressure washer hose into the spark plug hole and turn on the pressure. You get the same forces as on a hydraulic cylinder. If you use two pressure washers on the proper cylinders you can alternate from one washer to the other and move everything back and forth until it frees up. I've seen some pretty sorry looking motors freed up this way.
__________________
1940 Cab 11 C8 Wireless with 1A2 box & 11 set
1940 Cab 11 C8 cab and chassis
1940 Cab 11 C15 with 2A1 & Motley mount & Lewis gun
1940 Cab 11 F15A w/ Chev rear ends
1941 Cab 12 F15A
1942-44 Cab 13 F15A x 5
1942 cab 13 F15A with 2B1 box
1943 cab 13 F15A with 2H1 box
1943 Cab 13 C8A HUP
1944 Cab 13 C15A with 2C1 box
1943 Cletrac M2 High Speed Tractor
MkII Bren gun carrier chassis x 2
Reply With Quote
  #4  
Old 13-02-07, 13:52
charlie fitton's Avatar
charlie fitton charlie fitton is offline
HLIofC - Normandy Pl
 
Join Date: Aug 2004
Location: Maryhill Ontario
Posts: 942
Default stuck fords

Sad part is, it's more often than not the valves that stick first, so a compression check is in order as soon as you get the works spinning..... especially if it gets very easy - real soon.
__________________
Charles Fitton
Maryhill On.,
Canada

too many carriers
too many rovers
not enough time.
(and now a BSA...)
(and now a Triumph TRW...)
Reply With Quote
  #5  
Old 13-02-07, 18:12
Keith Webb's Avatar
Keith Webb Keith Webb is offline
Film maker, CMP addict
 
Join Date: Feb 2003
Location: Macleod, Victoria, Australia
Posts: 8,216
Default Rust

Back in the 70s I pulled a LOT of these engines down. Most which were seized had serious rust in them where water had entered via the carby. They invariably had rust in the two cylinders with open inlet valves. Sometimes what looked a bit sad wasn't too bad, but sometimes the only thing which would move them was to bash the pistons out downwards once the crankshaft had been removed. These motors would sometimes need sleeving, or be scrapped altogether.

The cracks Geoff mentions were very common in the vavle seat area, mostly on the later 8BA engines (in fact it was rare to find one without cracks) but uncommon in earlier motors like the Mercury.

My advice is to try the soaking methods others have mentioned first but be prepared for the worst.
__________________
Film maker

42 FGT No8 (Aust) remains
42 FGT No9 (Aust)
42 F15
Keith Webb
Macleod, Victoria Australia
Also Canadian Military Pattern Vehicles group on Facebook
https://www.facebook.com/groups/canadianmilitarypattern
Reply With Quote
  #6  
Old 13-02-07, 20:44
Dave Page Dave Page is offline
Registered User
 
Join Date: Mar 2004
Location: Virginia, USA
Posts: 161
Default

Hi,
try a pint or two of diesel fuel in each of the cylinders via the spark plug holes, and some down her throat (for the inlet valves) let it soak for a couple of days. Remove the cover from the flywheel and using a pry bar (not a screwdriver) in the ring gear, taking care not to remove a tooth. Inch the flywheel in each direction a bit at a time till she frees enough to allow free turning with the crank handle. You will achieve much more purchase against the ring gear than you or your strongest friend could ever assert with a crank handle.
Good luck,
Dave
Reply With Quote
  #7  
Old 13-02-07, 20:50
chris vickery's Avatar
chris vickery chris vickery is offline
3RD ECHELON WKSP
 
Join Date: Feb 2003
Location: Nipissing Ontario Canada
Posts: 2,955
Default

I concur with Keith on this one too. Having pulled apart several of these motors in the past few years I can say that all the soaking in the world is pretty much useless.
Of all the motors I have ever done, the only thing that worked was to pull the heads, pull the crank, and then proceed to beat the pistons out, usually with a large piece of hardwood and a big hammer.
Don't worry too much about hurting anything because at this point it is about wrecked anyhow. Finding a good flatty that isn't seized is like the needle in the haystack.
About the only one I ever had in this as found condition was one that had been lubed up regularily and was cranked over from time to time to keep everything free. Even so, some of the valves were stuck and needed to be freed up before it could be test fired.
__________________
3RD Echelon Wksp

1968 M274A5 Mule Baifield USMC
1966 M274A2 Mule BMY USMC
1958 M274 Mule Willys US Army
1970 M38A1 CDN3 70-08715 1 CSR
1981 MANAC 3/4T CDN trailer
1943 Converto Airborne Trailer
1983 M1009 CUCV

RT-524, PRC-77s,
and trucks and stuff and more stuff and and.......

OMVA, MVPA, G503, Steel Soldiers
Reply With Quote
  #8  
Old 14-02-07, 01:11
Snowtractor Snowtractor is offline
In Vino Veritas
 
Join Date: Feb 2003
Location: Northern ALberta
Posts: 981
Default flywheel

Quote:
Originally posted by Dave Page
Hi,
Remove the cover from the flywheel and using a pry bar (not a screwdriver) in the ring gear, taking care not to remove a tooth.
Good luck,
Dave
There is a flywheel tool specially designed for turning the flywheel without breaking a tooth or slipping. Princess auto has them , cheap, other tool places must have them too.
Sean
__________________
1944 Allis Chalmers M7 Snow Tractor
1944 Universal Carrier MKII
M9A1 International Halftrack
M38CDN 1952
Other stuff
Reply With Quote
  #9  
Old 15-02-07, 08:37
Bob Moseley (RIP)'s Avatar
Bob Moseley (RIP) Bob Moseley (RIP) is offline
RIP
 
Join Date: Feb 2003
Location: Adelaide, South Australia
Posts: 2,620
Default

Hi all
I'm not going to add to the welter of good advice but bear in mind that the Ford V8 is the benchmark of motors and you may just be suffering from their extreme high compression.
Bob
Reply With Quote
  #10  
Old 15-02-07, 10:34
maverick maverick is offline
Alan Bumford
 
Join Date: Oct 2006
Location: Swindon Wilts England
Posts: 93
Default

Thanks Bob It would be nice if it was but its seized, but with the wealth of advice coming in maybe not for long.
Reply With Quote
  #11  
Old 17-02-07, 15:01
marco marco is offline
Marco Hogenkamp
 
Join Date: Jan 2006
Location: Lichtenvoorde, Holland
Posts: 267
Default

Hello all,

When you are going to put in new pistons and the old ones can be trown away there is another trick which I used succesfully on a Cadillac 346 flathead Chaffee engine (after many alternatives failed):

Select a piston of which you are sure it is stuck.
From the top, drill a hole about 6mm diameter at the edge of the piston at a safe distance of about 10mm from the cilinder wall.
You might have to make an extension for your drill bit to have sufficient reach.
Drill as deep as you can get checking carefully not the hit the cilinder wall.

Once your through, replace the 6mm drill with a slightly larger drill and repeat the job, again checking carefully not to hit the cilinder wall.

The trick is to try to drill a hole as large as possible.
At a certain moment the wall of the piston is weakened enough to remove the tension between piston and cilinder wall.
Try to turn the crankshaft to see if it is coming free.
If not, pick out another stuck piston and repeat the job.

The method seems quite unconventional, but if done accurately it really works.

Marco
__________________
Staghound F215633, 12th Troop "Sergeants Car" XII Manitoba Dragoons
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 21:14.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016