MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Softskin Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 09-07-22, 10:56
Jakko Westerbeke Jakko Westerbeke is offline
Moderator
 
Join Date: Apr 2020
Location: Netherlands
Posts: 341
Default

Quote:
Originally Posted by Jack Geratic View Post
How was the the top strap secured/locked in place for this front rack style?
It looks like it’s a pin through holes in the vertical strips, but it’s hard to tell from this angle.

Quote:
Originally Posted by Ed Landstrom View Post
By the '70s, we thought the Pinto fuel tank location was bad. Standards do change.
It could be a water can …
Reply With Quote
  #2  
Old 09-07-22, 14:39
Jack Geratic Jack Geratic is offline
Registered User
 
Join Date: Nov 2011
Location: Ontario
Posts: 179
Default

.....................................
Attached Images
File Type: jpg crerar jeep stencil.jpg (437.6 KB, 17 views)
Reply With Quote
  #3  
Old 09-07-22, 14:42
Jack Geratic Jack Geratic is offline
Registered User
 
Join Date: Nov 2011
Location: Ontario
Posts: 179
Default

Thank you Jakko. The water can was a possible tertiary question to my thread, but not sure if Crerar's driving regime would require quick access to extra water?

Point noted about the rod sliding through the upper framework of the fuel rack. Found slightly different angle of the same jeep to confirm this. Just wondering how it was kept in place to prevent it from sliding out while driving?

monty crerars jeep.jpg
Reply With Quote
  #4  
Old 10-07-22, 10:57
Jakko Westerbeke Jakko Westerbeke is offline
Moderator
 
Join Date: Apr 2020
Location: Netherlands
Posts: 341
Default

Quote:
Originally Posted by Jack Geratic View Post
The water can was a possible tertiary question to my thread, but not sure if Crerar's driving regime would require quick access to extra water?
From the picture you posted as a screenshot of Acrobat Reader:

Crerar's Jeep.jpg

… I get the impression he had one of each — assuming it’s the same two jerrycans as in the other photos.

Quote:
Originally Posted by Jack Geratic View Post
Point noted about the rod sliding through the upper framework of the fuel rack. Found slightly different angle of the same jeep to confirm this. Just wondering how it was kept in place to prevent it from sliding out while driving?
From the photo above, there seems to be some kind of lock on the left-hand side. Could just be some kind of simple latch that prevents the pin from sliding out, or maybe it’s padlocked to prevent people stealing the cans? However, I can’t find any more photos of this particular jeep from the left-hand side on a quick search, nor a clearer version of this photo.

I just noticed the stars on the sides are completely point-down. I thought the normal way in the Canadian Army was point-forward, until it changed to point-up eventually?
Reply With Quote
  #5  
Old 11-07-22, 05:58
Jack Geratic Jack Geratic is offline
Registered User
 
Join Date: Nov 2011
Location: Ontario
Posts: 179
Default

Is it the stamped portion of the fuel can painted white indicating it contains water?

Anyhow, I went back to the same photo album to see if any helpful photos were missed. There is this one but quality of a contact sheet is not much help, but it does seem to be same as the opposite side.

fuel rack.jpg

Plus one more of a different serial jeep:

Crerar-jeep-CM4242267.jpg
Reply With Quote
  #6  
Old 11-07-22, 11:08
Jakko Westerbeke Jakko Westerbeke is offline
Moderator
 
Join Date: Apr 2020
Location: Netherlands
Posts: 341
Default

Quote:
Originally Posted by Jack Geratic View Post
Is it the stamped portion of the fuel can painted white indicating it contains water?
I think so, but I’m not sure why I think so

Quote:
Originally Posted by Jack Geratic View Post
Anyhow, I went back to the same photo album to see if any helpful photos were missed. There is this one but quality of a contact sheet is not much help, but it does seem to be same as the opposite side.
Very hard to see … It could just be flat bar with a narrow end to go through the slot on the right, while on the left side of the rack is a bend-over bit that the flat bar hooks into somehow? Maybe with a separate retaining pin though both the bar and the rack’s vertical strip?
Reply With Quote
  #7  
Old 11-07-22, 12:12
David Herbert David Herbert is offline
Registered User
 
Join Date: Mar 2010
Location: Ayrshire, Scotland - previously Suffolk
Posts: 563
Default

Yes, the white painted pressings in a jerrycan indicate that it is a dedicated water can.

David
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Bofors 40mm Spare barrel box question??? Rob Fast The Gun Park 26 04-11-23 18:08
Sold: Chorehorse Spare parts box and Fuel Funnel B. Harris For Sale Or Wanted 2 29-01-16 00:38
Spare parts list question Keith Webb The Softskin Forum 6 11-10-10 12:40
Bren spare barrel question Jordan Baker WW2 Military History & Equipment 8 17-01-06 01:02
spare wheel FOX armoured car question Stefan Leegwater The Armour Forum 4 12-12-05 07:30


All times are GMT +2. The time now is 15:28.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016