![]() |
|
#1
|
|||
|
|||
![]()
Bob
Without the help of you and the team, I am not sure I would have made it off the property with these. It would have been days longer, and an inch at a time. Without the help of many on this forum who contributed knowledge, gave or sold me parts, I would be much further back than I am now. Especially I would mention Hanno, who did all the leg work in his country to get me a lot of items I purchased from that auction out his way. He talked with the owner, picked up the goods, stored and prepped them for shipping, and made all the arrangements to have them shipped. Or Dave, who knew of the limbers and negotiated a deal on them. Or Wayne, who brought me out the tractor shell from his province. There are many many more to thank in this....I know they know who they are: Thanks. It was a team effort for sure. No man is an Island, and certainly not in this case. |
#2
|
|||
|
|||
![]()
Very nice result, Rob.
Mike |
#3
|
|||
|
|||
![]() Quote:
__________________
Terry Warner - 74-????? M151A2 - 70-08876 M38A1 - 53-71233 M100CDN trailer Beware! The Green Disease walks among us! |
#4
|
|||
|
|||
![]()
It was a rather nice day today, so after I put away the Christmas CMP 3 ton I used the tractor to pull one of the firing platforms out of the snowbank. I'll get it into the shop in the next day or two and after it thaws get a start on it. One spoke shows damage but I am pretty sure I can fix it without having to remove the spoke. My original plan was to remove the spoke, but there are a lot of rivets involved. I am going to plan B: heat, straighten and weld. I'll also get the crab legs off it, and mix them with the partial set I bought from the auction. Those are small enough I can get the individual pieces into the cabinet sandblaster. The platform will have to wait for spring.
If one goes back to the first page of all this, you will read that the platforms were a complete surprise. All the photos I saw were of guns without platform. When I got there the owner told me there were the big circles under the flower garden's earth. A nice surprise...those are not common here. |
#5
|
|||
|
|||
![]()
Some photos of the firing platform. I repaired the bent spoke, and replaced the metal underneath rather than try to straighten it. The crab legs gave some resistance, and to save oxyacetelyne I dropped the upper legs into the woodstove for 10 minutes. They came out slightly glowing red which softened up the pins and had them apart in reasonable time. Both of the "axles" for the arms were bent or broken, but it turns out they are fabricated, so it will be easy to make new ones. I have pushed the ring underneath the gun for now until spring, but will make the leg axles soon once I buy some metal from town.
Last edited by rob love; 20-01-21 at 23:56. |
#6
|
|||
|
|||
![]()
I thought the firing platform would take a while to sandblast, but it was done in a morning. I also have totally disassembled the attaching legs and cleaned all those up as well. One pin decided to shed it's threads, but I am glad it is a fairly simple pin. I'll try to salvage one off my spare set of legs, but if that doesn't work out it will be easy enough to make.
Tolerances on the pins and legs seem pretty tight and don't leave a lot of room for lubricant. I'll polish up the shafts on the pins which should give a few thou of tolerance. Otherwise they are close to a press fit. |
#7
|
|||
|
|||
![]()
I tried to salvaged another stripped pin and the next one I removed did the same thing. So I had one left to try, and by heating the bracket to a nice red colour, the pin came out with it's threads.
I re-sandblasted everything lightly to remove any oils, and followed up with a coat of POR15 and then the Gillespie OD. I had to re-polish any overspray off the pins, and clean some of the bores, but everything went together without issue. The platform is now on the gun, although I am going to have to make up some new pads on the trails, as the platform is loose and the one chain that adjusts will not go far enough to tighten the ring. I was able to put a twist in the two chains to get it all tight for now. I note lots of small jobs to do on the gun, like riveting some straps in place, and I have to make the wood seat yet, and also the case for the instrument lights. But today I towed it out of the shop to let the sun and heat help the fresh paint to cure. It will also let me "cut the grass" in the area of the shop that has housed this gun for the past two or three years. |
#8
|
|||
|
|||
![]()
So now it is time to move to the next portion of this restoration: the limber. I pulled the tarp off and brought it to the shop. I am hoping this will be a quick restoration. I removed the right tire which was missing it's snap-ring, and replaced it with a cmp rim and tire for now. The first order of business will be to remove the fenders, and straighten a few parts. With any luck I'll have it in the sandblast shed for August.
This was a Saskatchewan/Alberta piece, so is relatively rust free which is nice. I expect the fenders to give me the biggest problem. In the background you can just see the artillery tractor shell. The tractor will be made up from 3 different CMPs, and use a 15cwt frame which I believe to be pretty identical to the FAT frame. |
#9
|
||||
|
||||
![]() Quote:
Someone else in years to come might be the custodian of this gun and they might appreciate knowing the correct touch up. ![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|