![]() |
|
#1
|
|||
|
|||
![]()
Wow! That is a great looking early issue Curtain, Bruce.
At some production point, the second line became, COVERS WATERPROOF NO. C1, the next line became ZA/CAN 4764 and the CMC Part Number was dropped from it completely. The Parts Manuals as late as 1948 still referenced the existence of these earlier spare parts. You wouldn’t happen to have a competent canvas company in the neighbourhood would you? Never too soon to plan ahead. David |
#2
|
|||
|
|||
![]() Quote:
|
#3
|
|||
|
|||
![]()
Thanks, Bruce.
This has the makings of an interesting sub-project eventually. David |
#4
|
|||
|
|||
![]()
Sometimes in a large, complex project like this, you realize you need to perform a lateral move to keep the overall project on a correct track. I reached that point this weekend. The Testor’s paints I was hoping to get in the mail last week did not arrive, which will slow forward progress a little bit. I took the opportunity to skip ahead a bit to look at what work will be coming up that I will need these paints for and try and plan accordingly.
Once I have the 3-Wing BAND Switch finished and reinstalled, the next item I want to tackle is the restoration and reassembly of the FREQUENCY MC Dial assembly, located on the right side, centre of the Sender front panel. This entire assembly is identical to the one in the Receivers for the 52-Set, and it is between these two dials that the critical sync of the Receiver and Sender operating frequency is established. The FREQUENCY MC Dial on this Sender is in tough shape. The plating is almost entirely eaten away and rust around the rim is extensive. With some very careful cleaning, the Lower and Mid-Range Green and Yellow portions of the dial could probably be cleaned up reasonably well, but the High Range Orange portion on the opposite half of the dial may be too far gone to easily bring back. It also takes a good time under UV Light for all three portions of the dial to luminesce. The yellow portion is not too bad, but the Green and Orange portions fade off in just a few seconds. I knew I had a very good condition FREQUENCT MC Dial from the parts receiver, but when I checked it out, I remembered what I had done way back at the start of this project when only having the three receivers to work with. The Remote Receiver had a small white decal centred between the Meter and the Speaker indicating “NON-LUMINOUS DIAL”. Because of its position, and the fact the meter on the Remote Receiver was a different manufacturer’s product from the other two meters I had, I just assumed the decal was in reference to the Meter Dial. It was not until some time later, when I put the Remote Receiver front panel under UV Light that I realized it was the FREQUENCY MC Dial that was not fully luminous. I did not like that at the time and felt both receiver FREQUENCY MC Dials should match, so I took the fully luminous one off the parts receiver and placed it on my Remote Receiver. Fast Forward to now, and I realize the Remote Receiver is a stand alone item, and part of the history of my particular one is that it had its Meter and FREQUNCY MC Dial replaced at one time and that history should be preserved. SO…note to self, Put the non-luminous dial back on the Remote receiver and use the fully luminous dial on the Sender, if its own dial cannot be well restored. David |
#5
|
|||
|
|||
![]()
I was looking for a couple of items last evening and had my two Cases Spares sitting out on the floor. When I picked up the newer, minty green one to put it back on the shelf, something on the front of the case caught my eye. I thought I could see stencil marks. I put it down on its back and started playing with the lighting in the room. Sure enough. I could see the first two lines of the markings for this case that are illustrated in the Master Parts Listings:
CASE SPARES WIRELESS SET I pulled the water damaged grey case off the shelf and compared the shadows left on the wood on it to what I had just spotted on the green case. I can only just read the first two lines on the grey case and they matched perfectly to the green case and the manual. This morning, I gave the green case a closer look, and a VERY light partial sanding, and found the third line: CANADIAN NO. 52 I can also read CMC at the start of the 4th line with one ‘0’ near the end of it, and the numbers 9 and 3 at the end of the 5th and last line. Again I am amazed at the incredible detail the illustrators provided in the Master Parts List. David |
#6
|
|||
|
|||
![]()
What a great find!
__________________
V/R James D. Teel II Edmond, Oklahoma Retired Police Sergeant/Bomb Tech 1943 Willys MB/ITM jeep 1942 SS Cars No1Mk1 LtWt trailer |
#7
|
|||
|
|||
![]()
Hi James.
Yes indeed. I was quite pleased with that discovery. Just the Case, Operating, Remote Receiver to eventually take a closer look at now. No paints in the mail again today so I took advantage of that and finished cleaning the two PA LOADING Coils on the right side of the chassis and the rest of the lower, rear chassis deck. Went through about 30 Cotton cleaning sticks to reach all the fiddly places. The larger of the two 1.75 to 8.0 MC PA LOADING Coils cleaned up really well. On the front end I can now clearly read the Coil Serial Number and on the rear end, the CMC Stock Number for it. David |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Canadian staff car wireless: World War 2 Canadian R103 Receiver Demo | Mike K | The Wireless Forum | 5 | 24-07-16 15:20 |
Found: CMP Wireless body project | Jim Burrill | For Sale Or Wanted | 7 | 05-04-15 00:02 |
Canadian dehavilland mosquito restoration project | David Dunlop | WW2 Military History & Equipment | 9 | 10-07-14 00:51 |
Canadian project | David Ellery | The Carrier Forum | 9 | 28-04-07 01:36 |
FOR SALE/TRADE: 1944 CHOREHORSE PROJECT for Signal Corps Wireless Power Unit Project | Alain | For Sale Or Wanted | 1 | 21-02-07 00:11 |