MLU FORUM  

Go Back   MLU FORUM > GENERAL WW2 TOPICS > The Wireless Forum

Notices

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #11  
Old 30-08-20, 23:25
David Dunlop David Dunlop is offline
Registered User
 
Join Date: Feb 2006
Location: Winnipeg, MB, Canada
Posts: 3,599
Default AERIALS, Horizontal, 4-Section ZA/C 00087

Thank you for your comments, James.

As predicted, today has been a major rain and thunderstorm day, so no polishing, to which my fingers are eternally grateful!

Before the rains arrived, however, I did accomplish some good errands. I picked up another 75 ml tube of polish and found it is now pushing $18.00 Cdn a tube now, but still well worth it.

I also dropped into the local RONA and bought an 11 foot length of rubber sheathed 16/3 power cord to replace the one on the new CPP-2. when I feel up to moving it again.

The other thing I did was take a look at some modern electrical components I thought would be suitable replacements for fittings needed to eventually replicate the AERIALS, Horizontal, 4-Section used with the Wireless Set No. 52.

The 14 gauge 7/22 Hard Drawn stranded copper aerial wire is still readily available in the United States, but seems to have disappeared out of the usual Amateur Radio markets here in Canada. I am not about to order any at the moment though. I realized I now have 13 parcels sitting at my local US Border Mail Depot I cannot retrieve because the border is still closed. No need to be adding to that right now.

Geoff Turcott sent me a couple of detail photos of his 52-Set aerial and it looked like some modern items would be good fits.

The two attached photos from Geoff show the Section quick connect/disconnect fittings, and the splice fitting between the end of the aerial and the Feeder Cable to the Set.

The third photo shows the modern substitutes I found, They are all MARR 14 gauge crimp connectors. The photo shows the packaging, the fitting with blue insulation attached and with the insulation peeled off. The Male/Female Bullets will work nicely for the Section Connections and the Butt Splice Connector for the Aerial to Feeder Splice. I will crimp them all as well as solder the fittings, when I get to that part of the project.

One other fitting to look into locally and that part of the project should be good to go.

David
Attached Images
File Type: jpg AERIAL Section Connector.JPG (481.5 KB, 2 views)
File Type: jpg AERIAL, Butt Connector.JPG (450.8 KB, 1 views)
File Type: jpg MARR 14 Ga Crimp Connectors.JPG (174.8 KB, 2 views)
Reply With Quote
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Canadian staff car wireless: World War 2 Canadian R103 Receiver Demo Mike K The Wireless Forum 5 24-07-16 15:20
Found: CMP Wireless body project Jim Burrill For Sale Or Wanted 7 05-04-15 00:02
Canadian dehavilland mosquito restoration project David Dunlop WW2 Military History & Equipment 9 10-07-14 00:51
Canadian project David Ellery The Carrier Forum 9 28-04-07 01:36
FOR SALE/TRADE: 1944 CHOREHORSE PROJECT for Signal Corps Wireless Power Unit Project Alain For Sale Or Wanted 1 21-02-07 00:11


All times are GMT +2. The time now is 11:17.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016