Lynx I MkIII purchase

[Alastair Thomas]

Thanks everyone. I must say that I was particularly doubtful about the "SLING HERE" sign but we now know it is correct.
Alastair
F60S LAAT
Lynx I MkIII*

[Davdberg]

Hey guys,

I was wondering if you could help me out. Are the axles and gear box on the Lynx Scout similar to any CMP Ford trucks? A friend of mine is looking at a project but its lacking axles; gearbox and engine. Chassis is unknown.

Best regards

[Harry Moon]

my understanding is the Lynx1 has F8A axles and the Lynx2 has F15A axles but 63 inchs centre to centre.

[Andrew Rowe]

The Mk 1 is 12 spline and the Mk 2 Lynx axle is 16 splines. Lynx 1 is of a smaller diameter than Mk2. The axles from a C8A (maybe F8 as well ?)are the right length but are 10 spline. They have the correct flange thickness and 8 hole bolt up pattern. The short one is about 678mm to the inside of the flange. My theory is that you can get a C8A axle and vee the spline a little deeper and weld up and then re-cut the new spline to 12, if making a Mk1 axle. The other idea is to take the longer axle from the other side and cut it down to a short side length and then re-cut the spline. The axles I believe are just case hardened so with modern carbide cutters, can do the job. Using a C8A axle is about 38mm thick, this will get turned down to about 34.8mm where the spline needs cutting, this is for Lynx 1 only. The Lynx 2 starts with an axle that is about 43.8mm dia. , so quite possible other axles in the CMP range would work, the spline is 16 , so would have to check that against a larger CMP axle.
The Lynx gearbox uses standard Ford 4-speed truck gearbox components, but the housing is different. They have turned the main part of the gearbox 90 degree to the bellhousing part of the casting that bolts to the engine, so to give you a flat floor. The shifter housing that bolts to the side is all enclosed and uses double shifter rods to make the gearchanges remotely, if that makes sense.I Have cast up new gearboxes for the Lynx, but have still to machine them up at this stage.
Just to add some technical info:
Lynx 1 axle: 12 spline, 34.8mm at the spline dia. approx., length of spline 65mm, inner axle diff seal runs about 130mm from end
of the axle, ( spline end ) Short side axle is 678mm from the end to the inner of the flange, Long axle is 1048mm to
the inner of the flange. The flange is about 1/2" thick and about 134mm dia. with 8 holes @ 114mm dia., NO
counter sunk drilled for these holes like other CMP axles.

Lynx 2 Axle: 16 spline, 43.8mm at the spline dia. approx., length of spline 80mm, inner axle seal runs about 90mm from the end
of the axle ( spline end ). Short axle is 678mm to the inner of the flange and long is 1048mm to the inner of the
flange. Flange and holes are the same as Lynx 1.

If anyone is passing by a bunch of CMP F8 or F15 axles, it would be interesting to see what these measure at? I do know C8AX axles , could be converted to Lynx 1 as I have mentioned above as they are the right length and start life at about 38mm, so there is enough meat to work with when re-machining......if my theory works out?

Cheers Andrew.

[lynx42]

Originally Posted by Andrew Rowe

The Mk 1 is 12 spline and the Mk 2 Lynx axle is 16 splines. Lynx 1 is of a smaller diameter than Mk2. The axles from a C8A (maybe F8 as well ?)are the right length but are 10 spline. They have the correct flange thickness and 8 hole bolt up pattern.

r6eoet7apnyz.jpg

Andrew, Lynx 1 Mk's 1,11,111, and 111* all have 6 stud bolt set up not 8. The wheels are like those on the Chev HUP's. The tyre size is also unusual at 9.25" x 16. I am running 9.00X16 tyres as the others are not available.

Lynx continues 072.JPG

A bit of a difference in rolling circumference, but that shouldn't cause me too many problems.

Lynx Continues Tyres 025.JPG




I was luck to get my original gearbox. You will have a few blokes looking out for your new cast housings as I have had many enquiries re the gearbox availability.

Cheers Rick.

[Andrew Rowe]

Hi Rick, with regards to the axles, I was talking about the axle flange that bolts to the inner hub is 8 bolts on ALL models.
You are talking about the wheel rims, that use 6 stud Wheel nuts on Lynx 1 and
8 stud Wheel nuts on Lynx 2. The 6 stud wheel rims are of lighter construction than the 8 stud wheel rims, which use the standard heavier CMP 9.00 x 16 rim on the Lynx 2. With regards to my gearboxes, I have to find a friendly guy ( meaning cheap !) with a CNC centre mill/lathe? to program the line- boring of the holes and the facing off of the surfaces. All hole and face dimensions are that of the standard Ford 4 speed "crash" gearbox. They are excellent quality castings ready for machining, Calling anybody out there with the skill and equipment! , Cheers Andrew

[Andrew Rowe]

I probably went off on a tangent talking about axles....too much covid lockdown! , I guess if you were talking differentials, there were 3 types for the Lynx, serial 0 to 201 was a 5.83 ratio with 14 &7/8" across the width of the flange housing , serial 201 to 3000 is 5.83ratio and is 12&1/4" across the width of the flange housing, from serial number 3000 the ratio is 6.66 and is 14 &7/8" across the flange housing. This last diff is basically looks like the same
dimensions as the standard Ford 3 ton axle, similar to Bren Carriers, except they use C8A backing plates and the axles are different lengths., Cheers A.

[Harry Moon]

Originally Posted by Andrew Rowe

Hi Rick, with regards to the axles, I was talking about the axle flange that bolts to the inner hub is 8 bolts on ALL models.
You are talking about the wheel rims, that use 6 stud Wheel nuts on Lynx 1 and
8 stud Wheel nuts on Lynx 2. The 6 stud wheel rims are of lighter construction than the 8 stud wheel rims, which use the standard heavier CMP 9.00 x 16 rim on the Lynx 2. With regards to my gearboxes, I have to find a friendly guy ( meaning cheap !) with a CNC centre mill/lathe? to program the line- boring of the holes and the facing off of the surfaces. All hole and face dimensions are that of the standard Ford 4 speed "crash" gearbox. They are excellent quality castings ready for machining, Calling anybody out there with the skill and equipment! , Cheers Andrew

What I understand is that the transmission, remote shifter, clutch and throttle controls on the Lynx1 are all of the shelf from the bus operations at Ford. So a source for a transmission could be an old 36-42 Ford powered Bus.