MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Armour Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 24-01-18, 14:48
RichardT10829's Avatar
RichardT10829 RichardT10829 is offline
Richard Harrison
 
Join Date: Nov 2008
Location: Cullercoats Newcastle Upon Tyne United Kingdom
Posts: 3,068
Default

Looking fantastic Colin. Would that be Naftoseal being applied by junior ? Also known as Choccy sauce
__________________
is mos redintegro

__5th Div___46th Div__
1942 Ford Universal Carrier No.3 MkI*
Lower Hull No. 10131
War Department CT54508 (SOLD)
1944 Ford Universal Carrier MkII* (under restoration).
1944 Morris C8 radio body (under restoration).
Reply With Quote
  #2  
Old 25-01-18, 09:10
colin jones's Avatar
colin jones colin jones is offline
Registered User
 
Join Date: Jun 2007
Location: Adelaide
Posts: 1,810
Default

James, Richard, the wind chill is about 45 coming from the north and I did have a few cold ones we are about to get the next 3-4 days of extremely hot above 40 out here but I will keep plodding along. The sealant Andrew was putting on the fuel tanks is aviation sealant my wife bring home from work when it's out of date to use on aircraft but still has lots of time left for ground use. The RAAF won't use any if it is even one day past its useby date. Bad for them great for me .
I have been continuing on the back to get them both finished.
Attached Images
File Type: jpg 20180123_083245.jpg (161.1 KB, 1 views)
File Type: jpg 20180123_095353.jpg (231.0 KB, 1 views)
File Type: jpg 20180123_152526.jpg (165.1 KB, 4 views)
File Type: jpg 20180123_152629.jpg (151.5 KB, 3 views)
File Type: jpg 20180124_153925.jpg (183.6 KB, 2 views)
Reply With Quote
  #3  
Old 25-01-18, 09:14
colin jones's Avatar
colin jones colin jones is offline
Registered User
 
Join Date: Jun 2007
Location: Adelaide
Posts: 1,810
Default

The wishbone shape part is for support for the crank handle. It swings down when required and the crank handle is inserted and I just happened to have an original crank handle as well . The other shaped part is for storage of a cammo net or tarp.
Attached Images
File Type: jpg 20180124_153936.jpg (146.3 KB, 1 views)
File Type: jpg 20180124_171346.jpg (157.9 KB, 1 views)
File Type: jpg 20180125_073851.jpg (172.9 KB, 1 views)
File Type: jpg 20180125_141558.jpg (120.3 KB, 1 views)
File Type: jpg 20180125_141603.jpg (125.2 KB, 1 views)
Reply With Quote
  #4  
Old 25-01-18, 09:20
colin jones's Avatar
colin jones colin jones is offline
Registered User
 
Join Date: Jun 2007
Location: Adelaide
Posts: 1,810
Default

The press tooling I made is for the fuel tank cover. It has a dished recess for I assume a soft rubber compound to sit in under the lid. As I only need two of these I never put too much weld on them so I can easily disassemble and reuse the material again, much like most of my tooling. I will get them both completed within the next 2-3 days.
Attached Images
File Type: jpg 20180125_141612.jpg (118.7 KB, 2 views)
File Type: jpg 20180125_181758.jpg (178.8 KB, 3 views)
File Type: jpg 20180125_181809.jpg (144.0 KB, 3 views)
File Type: jpg 20180125_181821.jpg (151.8 KB, 3 views)
Reply With Quote
  #5  
Old 28-01-18, 03:36
colin jones's Avatar
colin jones colin jones is offline
Registered User
 
Join Date: Jun 2007
Location: Adelaide
Posts: 1,810
Default

I have just about completed both the backs apart from the fuel doors.
Attached Images
File Type: jpg 20180126_102345.jpg (179.5 KB, 2 views)
File Type: jpg 20180126_125602.jpg (236.1 KB, 3 views)
File Type: jpg 20180126_142847.jpg (225.3 KB, 2 views)
File Type: jpg 20180128_091019.jpg (152.7 KB, 2 views)
Reply With Quote
  #6  
Old 28-01-18, 03:38
colin jones's Avatar
colin jones colin jones is offline
Registered User
 
Join Date: Jun 2007
Location: Adelaide
Posts: 1,810
Default

The rear plate has some holes that bolts go through and some are tapped. After spraying the parts today they were dry in about 30 seconds as it is pushing 43-44 degrees hear. Not so good working but great for painting.
Reply With Quote
  #7  
Old 28-01-18, 03:40
colin jones's Avatar
colin jones colin jones is offline
Registered User
 
Join Date: Jun 2007
Location: Adelaide
Posts: 1,810
Default

And I forgot to post the pictures from the last post must be the heat
Attached Images
File Type: jpg 20180128_100254.jpg (125.5 KB, 3 views)
File Type: jpg 20180128_100304.jpg (207.0 KB, 5 views)
File Type: jpg 20180128_124957.jpg (190.9 KB, 7 views)
File Type: jpg 20180128_125008.jpg (165.3 KB, 7 views)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Door Resto Barry Churcher The Restoration Forum 13 15-05-22 15:36
FAT cab 13 No 9 resto Mrs Vampire The Softskin Forum 27 29-09-21 06:11
C15A resto harrygrey382 The Restoration Forum 9 08-06-15 09:40
another CAN m37 resto Steve Wilson The Restoration Forum 11 25-08-12 15:57
m 37 resto in new brunswick pauljboudreau Post-war Military Vehicles 118 07-03-11 22:29


All times are GMT +2. The time now is 02:00.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016