![]() |
|
#1
|
||||
|
||||
![]() Quote:
That is what I am after. I want to do a timber back as it is somewhat lighter than the steel ones. The old girl doesn't need any extra weight so I will follow your lead. I will probably have a million questions to ask in time. I bought Blueprint for Victory many years ago, which has some very good photographs. Ahh well, I can put it on the 'to do' list now. Cheers, Ian
__________________
Ian Williams F15A, 2x Army Land Rover 88' sIIA's GPW Other stuff |
#2
|
|||
|
|||
![]()
G'day Ian,
I have not got drawings for timber tray mate! But I did build one for my Fordson WOT2h truck if you like I could build you one if you are interested, I try to upload some photo's of my tray but it didn't work so Ian have a look at my FB page you will see some there. Regards Ian ![]()
__________________
1944 Mb Jeep (Restored) 1943 Gpw Jeep 1944 No3a Trailer (Fmc) 1945 No4 Trailer (Fmc) (Restored) 1941 Fordson WOT-2H 194? G506 Chevy truck (Yankee Joe) |
#3
|
|||
|
|||
![]() Quote:
You may be surprised at the weight of a steel body. I can lift the sides, front panel, and tailgate individually on my 15 CWT body. The floor is a different matter however! I have attached a few drawings I made in the 90's from an original rusted out floor when I thought I would replace it with a scratch built one. May give you some food for thought. It is pretty much a large sheet metal brake job, spot welded together. The only difficult fabrication I could see is the stiffeners on the sides, front, and tailgate shown in photo at the top. I never made drawings for the sides and tailgate as they were in reasonably good shape. Should you want to go the steel body route I could knock out some drawings of them this winter. Cheers, 15 CWT floor-top.jpg 15 CWT floor-underside.jpg 15 CWT floor-crossmembers.jpg IMG_1158.jpg
__________________
F15-A 1942 Battery Staff Jacques Reed |
#4
|
||||
|
||||
![]() Quote:
I really don't know what to say. This is great. Now I am beginning to think Steel Body, though my skill is in timber. Winter is a fair way away for you so that give me time to decide. Cheers, Ian
__________________
Ian Williams F15A, 2x Army Land Rover 88' sIIA's GPW Other stuff |
#5
|
|||
|
|||
![]()
Hi Ian,
Found another drawing- location of the 72 cage nuts used to attach the valance panels and the sides to the floor. A friend with patience and a heavy duty spot welder would come in handy for doing that job! Cheers,
__________________
F15-A 1942 Battery Staff Jacques Reed |
#6
|
|||
|
|||
![]()
From Hanno:
"Contrary to popular belief, only the cross members were made of hardwood, the planking was softwood so you would be good using pine. I'll look up the thread with that info later." For Canadian (and British?) wood trays, but doesn't apply in Australia. The trays were a local pattern and made of hardwood. Jacques: or if a big spot welder is not available (as it isn't for many of us I suspect), use the drill-and-weld method. Drill small holes in one side of the pair to be welded, then weld through the hole to the undrilled-other half. With small holes, 'dabbing' the arc and grinding off, it leaves a neat 'spot'. Regards Mike |
#7
|
||||
|
||||
![]() Quote:
Note the thicknesses of the boards and the types of wood used in the construction of these bodies. The British even published an Electrical and Mechanical Engineering Regulation (EMER) for wood specifying the various types of timber to use on vehicles - see HMVF forum: Timber for old MV's Canadian%2015-cwt%202H1%20body%20construction.jpg
__________________
Regards, Hanno -------------------------- |
#8
|
||||
|
||||
![]() Quote:
HTH, Hanno
__________________
Regards, Hanno -------------------------- |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Gotfredson 4B1 Ammo body drawing | Charlie Down | The Softskin Forum | 4 | 02-01-21 15:08 |
Lindsay Steel Body Construction | mlombard | The Softskin Forum | 12 | 09-09-16 23:20 |
Reference: 30-cwt - 3 ton 3C1 GS Steel body (Q.M.G.) | Hanno Spoelstra | The Restoration Forum | 4 | 12-04-16 13:52 |
Steel Body Manufacturers | Steve Guthrie | The Softskin Forum | 3 | 14-07-10 17:18 |
Steel body and spare wheel carrier F15A | Manfred Müllner | The Restoration Forum | 1 | 17-11-04 11:27 |