2014 at the Hammond Barn

[RHClarke]

Originally Posted by Bob Carriere

I beleive Stuart as meet the necessary requirements to be move from apprentice scrounger to full Rotter member of the barn. ...

The only remaining rite of initiation is for Stuart to break bread with the founding members at a Rockland eatery. Until then, welcome to the fold, Stuart. Lucifer feeding and care will be the next lesson for your apprenticeship
papers.

[Stuart Fedak]

Rob,
Thank you for your support.

Bob has begun the process for me to learn the satanic rights of the care and feeding of Lucifer. I am still struggling learning the chants in both official languages of the Hammond barn. According to Bob, it is acceptable to curse in either official language, when one hits a thumb, or breaks a rusted bolt whilst working at the barn.

I am sure that the Hammond crew will get lots of use from the two brake press. Thanks to our benefactor for making this purchase from his pension funds.....

Cheers!
Stuart

[RHClarke]

It's that time of the year again, and the boys at the Hammond Barn wish you and yours a happy or merry Christmas!

[Wpns 421]

To all Carolle and I would like to wish you the best in the New Year. May all your dreams of that once in a life time Barn Find be fulfilled. Oh yea Health and happiness.
The barn has taken on an awesomw apprentice in Stuart, since he has grown a beard he will now be hard to distiquish when you go on the "Raids"
Do you think they will make a movie? I see it now "THE HAMMOND BARN RAIDERS STRIKE AGAIN", They will probably make sequels. If not a movie then maybe a tv series like Highway from Hell.
Well enough for now, Carolle and I are off to New Zealand and Austrailia in January and we already have a show lined up so we will bring back pictures.

P.S. Ican carry a few small items???? and no differentials and engines are not small.

Best wishes
Carolle & Gilles

[Bob Carriere]

If not a movie then maybe a tv series like Highway from Hell.

...or Highway from Hammond.

All The Best to you and Carolle and the Boys from the Motahw Pool.

Safe trip to New Zealand ........

Bob C

[RHClarke]

6oC! Almost all of the snow is gone from the barnyard. There is a good layer of ice, and where the ground is exposed, mud. Lots of mud. So today, we took advantage of the good weather and set about with some tasks. Bob and Grant played around with Bob's CMP truck, which mysteriously decided to shatter a push rod. Bob can fill you in on that item.

Grant also got busy with mass producing metal signs for CMP trailers, while I worked on my M37 fender and did some M37 rim painting. After that fun I worked on one of the prototype's front fenders, which was well and truly rusted. The remainder of the afternoon was spent cutting away thin metal to prep for welding in the future.

Bob fixed his pushrod problem then began work on one of the greatest puzzles in the CMP world: his windshield. I am not sure if it is a cab 11 or cab 12 windshield, but it sure looked complicated. Good old Brit engineering, wot?

As usual, time expired and we headed back to our domestic chores, but it was a nice day at the barn.

Photos:

1- Bob and Grant troubleshooting Bob's Chev;
2 - Dodge rims drying in the warm (relatively) afternoon air;
3 - Barn decorations part 1
4 - Barn decorations part 2 (festive, eh?)

[Bob Carriere]

So much easier to work on the truck inside the barn where it is 60F rather than outside even if the weather is mild.

So I need to drive out the farm tractor/snowblower from the barn and fetch the Cab 11 from the sea container

Engine had not been runned for at least a month so it needed the choke and cranked a few trun before firing up. Now running the engine inside the steel sea container is always a bit loud but this morning the valves were clacking exceptionally loud...... close the choke and drove her out slowly...... still clacking but not as loud once outside the can. Drove to the barn and that cold morning clack just did not go away.

Drove it out of the barn so I could let it idle without posioning ourselves.

The clacking did not go away... played with the throttle but higher revs just made more noise... in front somewhere.

Popped the valve cover and promptly lost one of the original screws in the mud.

Took me a minute to restart the engine and walk around to the driver's side.... there she was.... a loose push rod.... loose hell half the top ring was missing.
Turned the engine off and carefully fished the missing part with tweezers.... must have just happened as the part could have rolled down in the head drain holes right into the pan.

Never seen a push rod fracture like that. Clean break and seemingly a fresh break.

Grant and I scrambled to see what spare parts we had...... found some badly rusted.... found some too short... then in the attic wrapped in plastic was a full set of the proper lenght.

Removed the old one, cleaned the replacement and dropped it in place. Did not want to spend a lot of time readjusting all the valve setting so I eye balled it, fired up the engine and adjusted the play by feel...... with the engine running you can see and feel the push rods spinning between your fingers so I adjusted, by comparaison, until too snug and too loose until she behaved like all the others. Will probably redo all the valves setting in the spring when I can get the engine properly hot.

If interested it was the intake rocker cyl. 2

Somedays you are just lucky enough to break something in your own driveway with all your tools handy.

Cheers