|
|
|
|
#1
18-11-12, 21:08
|
|||
|
|||
Quote:
thank you for your time and trouble in locating and initially doing all this work, it is much appreciated and shows how helpfull MLU can be. Regards Andy
__________________
Andy C15A Bsa parabike Landrover 86" TX1 London Taxi Bonneville Monkey bike 1943 GPW Australian 
|
|
#2
19-11-12, 00:10
|
|||
|
|||
|
CMP box
I still have to get the drawing and measurements yet .Out of sixty plans there should be somone that has them . I could take my box off and measure it as a last resort . Keep in toutch george
__________________
George is hooked on OD 5 window DT969 8 ton Fruehauf trailer M2A1Halftrack ,CMP #11 F15A1 #13 F15A1 RAF Fordson Tractor, 42 WLC HD No.2MK11 CT267514 center CB24713 bottom hull25701 ,No.2 MK2 parts MK1 10128 ,(2) MK1 ,Parts Hull9305 .Hull 10407 Hull plate # 7250 all have walk plate on back steps 1917 Patent modle amphibious army tank
|
|
#3
19-11-12, 00:43
|
|||
|
|||
|
Between the photos Bob posted and the files attached to my postings above (#7 and #8) I think the whole package is covered: sketches with dimensions, assembly instructions and photos.
|
|
#4
19-11-12, 01:35
|
|||
|
|||
|
The collective wisdom strikes!
Isn't it nice to have friends?
__________________
Terry Warner - 74-????? M151A2 - 70-08876 M38A1 - 53-71233 M100CDN trailer Beware! The Green Disease walks among us!
|
|
#5
19-11-12, 17:38
|
|||
|
|||
|
CMP box
Thanks Grant . I couldn't open your post until I down loaded Adoby on this new computer . I see them now . To make the clamps if you have a clamp for a pattern ,you make two molds with cement using the clamp for a pattern, and two rods for lining up the clamps ,Add some metal reinforcing bars in the cement . When it is hard put a sheet of flat iron ruff cut a bit bigger then you need in between and press them together to shape a new clamp. Trim to size when done .I think a little grease on the molds would help also . When pressing I would put a heavy plate on each side so as not to crack the cement PS I had sent a copy to Mike Timoshyk at Windsor ONT .He made a box and posted here when he restored his F15 CMP .I saw him on History Channel pulling two carriers out of the bush to restore last week Small world
__________________
George is hooked on OD 5 window DT969 8 ton Fruehauf trailer M2A1Halftrack ,CMP #11 F15A1 #13 F15A1 RAF Fordson Tractor, 42 WLC HD No.2MK11 CT267514 center CB24713 bottom hull25701 ,No.2 MK2 parts MK1 10128 ,(2) MK1 ,Parts Hull9305 .Hull 10407 Hull plate # 7250 all have walk plate on back steps 1917 Patent modle amphibious army tank
|
|
#6
20-11-12, 00:26
|
|||
|
|||
|
How is the bottom in the tool box attached? Rivets?
I have a toolbox with a repaired bottom that is attached temporarely with bolts. Will post pics as soon as I get it from the sand blaster. Svenn
|
|
#7
20-10-15, 20:12
|
||||
|
||||
|
Hanno, this thread has the info you were asking about with regards to the pivots.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| M37 spare tire wing nut $50 | Les Fisher | For Sale Or Wanted | 0 | 28-01-20 21:18 |
| Reference: Ford CMP Truck- Battery Holder plans | Jacques Reed | The Restoration Forum | 14 | 17-09-12 22:35 |
| Sold: 15 cwt Spare Tire Carrier/ Tool Box | Colin Alford | For Sale Or Wanted | 7 | 19-03-10 01:52 |
| Reference: Plans How to build a tool box for a CMP truck | S. Dafoe | The Restoration Forum | 152 | 06-07-09 00:54 |
| Vickers spare barrel holder | ron | The Carrier Forum | 11 | 28-05-09 17:08 |
Hybrid Mode
