Carrier wheel re rubbering got a group deal !

[kevin powles]

Hi Rich, I have a minimum of six to give you maybe more, Is it worth getting a trial wheel done to see how it looks and performs on a carrier?, It needs to last another 70 years also whats the best way in getting the old rubber off, I know it is probably burning it off but wont this effect the wheel casting?, also what finish do you need on the wheel surface to be rubbered, all remains of rubber removed then shot blasted to provide a key?.

just floating a few questions out there.

kevin.

[RichardT10829]

he did not specify just that all remnants of the rubber be removed. if you wanted a single wheel done first it would cost £70 i hear you loud and clear about its longevity so it may be an idea..... problem is my carrier is not mobile as yet As for blasting..... as you have access to a machine i would do them so when they come back they will be ready to go. I would do mine if i had access to a blaster hahaha. The rims have a beaded surface where the rubber meets them, or the wheels i have seen do..

my thoughts for removal were to the remains into section and knock off the rubber, whats left could either be grit blasted clean, wired brushed (using a mandrell on a grinder) or burnt off. as long as you dont heat the metal glowing hot you should be ok a gas torch would do the trick (this way is the least enviromentally friendly way to do it, and i will avoid this method if i can) i reckon if they were to be acid dipped the rubber would just fall off, ie costic cleaners down the road


EDIT: ps Kevin floating questions out there is exactly what we need to be doing buddy ! Your sand guards are now ready btw.


Richie

[cantankrs]

Originally Posted by RichardT10829

...whats left could either be grit blasted clean... ...i reckon if they were to be acid dipped the rubber would just fall off

Hi Richie,

Good thread going here.

Just my 2c worth. My observation with rubber (and grease) and abrasive blasting is that the impact of the grit gets absorbed and tends to bounce off. So the item needs to be fairly well degreased and any rubber practically all removed. Also possibly the blaster may not want to uneccesarily contaminate the grit as they may reuse it a few times.

Also I'm not sure that acid reacts much to rubber.

Checkout Bob Moseley's earlier thread on this carrier wheel rubber removal subject.

The interesting thing about Bob's pics is that the rubber appears not to be burnt up and consumed, but appears to be heated to the point where it releases and thus stays relatively intact. Dousing the hot rubber afterwards with water might reduce the environmental impact.

Good Luck!!

Regards

Alex

[cantankrs]

Also, again referring to Bob Moseley's thread, sufficient heat is probably key. Being able to get the rubber hot quickly such that it releases before it starts to cook, and before the wheel absorbs too much heat.

Alex.

[Philliphastings]

An excellent post... Getting the rubber off the roadwheels I have might not be too difficult as it has hardened to the consistency of coal and shatters on impact !

I have a few spare narrowed Australian wheels with brittle rubber but then again what I really will need in the fullness of time is a set of genuine british narrow wheels with good or new rubber - then there are the british pattern idlers which are different again. I have a pair of originals fitted but they too are fragile.

Getting more narrowed Australian Pattern wheels (as generous as the offer is) probably wo'nt solve the problem of originality for me.

I'm looking at ways to raise the money, bite the bullet and have a set of authentic English rims re-rubbered and shipped to West Australia.

Cheers

Phill

[ron]

Hi Phil,
Regarding the English wheels that you require, check your P Ms,
Regards Ron

[Doghouse]

HI Richard- great news! just caught up with the thread- I need a full set of wheels done as they are all pretty shot- however as the carrier's running and will be tied up over the next few weeks (being the season.... ) I wouldnt be able to get the wheels over for a few weeks- would your man sitll be able to help??
Keep up the excellend work and hard bargaining, ye great geordie lad ye!
regards from Ireland
David