![]() |
|
#1
|
|||
|
|||
![]()
Very nice indeed
|
#2
|
||||
|
||||
![]()
some more i hope
__________________
kenney |
#3
|
|||
|
|||
![]()
Great work Ken, looks very good. Not bad for a panel beater.
Have you changed the cab roof? I think I remember it being a Korean war cab. Tell us about the new electrics. Cheers, Terry
__________________
Terry F30 13 Cab CMP Morris Commercial C8 |
#4
|
||||
|
||||
![]()
Thanks for your kind remarks guys,Yes Terry it did have a Korean war cab but i wanted a 42 style cab,the back panels were replaced and some repairs done to the roof.
I would do it differently now though as the info 10 yrs ago was limited owing to not having a computer,and i have learned a lot since then working on other peoples 13 cabs. the wiring system is still 6v with all the correct sizing of wire in place with modern fuses and all put into modern plastic ribbed sleaving ,i know this is not original but i am looking for durability for the system ,why 6v you may ask, well after having starting problems some time ago Alex Blair suggested i put an earth from the battery earthing point to the bell housing/starter area and the result was that it started like it was on 12v,and 12v generators for the v8 are thin on the ground here, but 6v are still obtainable at swat meets etc
__________________
kenney |
#5
|
|||
|
|||
![]()
Cool tyres too Ken. Do you have a source for any more?
__________________
Terry F30 13 Cab CMP Morris Commercial C8 |
#6
|
||||
|
||||
![]()
They are run flat tires Terry,they may give a hard ride though.
__________________
kenney |
#7
|
|||
|
|||
![]() Quote:
The truck looks great and I'm glad my little tip helped with your starting problem..On six volt systems ,grounding is 90% of starting and rough running ,missing and all sorts of dim lighting and funny crap that goes on in electrical systems..and radio systems.. Just an example that someone figured out long ago is wireless radio military vehicle grounding..there are ground straps from every nut and bolt practically to every other nut and bolt and body part.. Some times when we do restorations we forget the importance of these grounds and leave them off or forget to replace them..even if we are not doing a lot of radio transmission and receiving.. But our electrical systems in the truck itself depends on it..Can't have too many ground straps on a 6 Volt system..Another thing I used to do was use welder's cable for heavy duty cables like starter and battery cables..they carry the amperage and voltage much better as they are braided with very flexible copper wire.. Makes all the difference in the electrical system.. Braided ground strap is great to use too. Glad things worked out well for you.. My mom always thought I was wasting my time and that I should have been studying when I was working on my old flat head Fords.. I guess it was an education of the fun kind.. Always stood me in good stead.. ![]() ![]() ![]()
__________________
Alex Blair :remember :support :drunk: |
#8
|
|||
|
|||
![]()
Hi All
The point of needing good "grounds" "earths" is very important with any voltage, I have 3 CMPs all with 6 volt system and normally they all start well with the 6 volt systems. BUT as Alex says you can not under state the need for good grounds between the engine and the frame is very important. Some of my Chevy CMPs had a woven ground strap between the engine and frame, one had no evidence of one. Without the ground strap you are dependent on a connection through the drive train not good, front engine mount rubber, rear engine mounts steel to steel but not necessarily good particularly if all the parts are well painted. If your truck doesn't have a good earth/ground strap take Alex's tip add a length of welding cable from the bell housing to the frame. I ran mine from the housing over to the same bolt that connects the battery ground strap to the frame. Starting problems from poor grounding increase if the engine is bigger or has increased compression. For example my C60S has a 261 cubic inch engine and starts just fine 95 times out of 100 with the six volt battery. The other 5 times were a problem, solution as the truck is equipped with a 12 volt battery to power radio equipment which hidden behind the 6 volt. I installed a marine battery switch which allows me to connect just the starter to the 12 volt, result instant start with out changing any of the other wiring on the truck.
__________________
Phil Waterman `41 C60L Pattern 12 `42 C60S Radio Pattern 13 `45 HUP http://canadianmilitarypattern.com/ New e-mail Philip@canadianmilitarypattern.com |
#9
|
||||
|
||||
![]()
A friend who done this wiring (has a C8AX) has put numerous earths in place that i have seen,on the dash board and such.
__________________
kenney |
#10
|
||||
|
||||
![]()
Looks great Ken, well done!
Quote:
Thanks, Hanno
__________________
Regards, Hanno -------------------------- |
#11
|
||||
|
||||
![]() Quote:
![]() |
#12
|
|||
|
|||
![]() Quote:
Regards, Terry
__________________
Terry F30 13 Cab CMP Morris Commercial C8 |
#13
|
|||
|
|||
![]()
The photo looks to my eyes as if the design was done to eliminate compound curves that would have required a large stamping press. A small run of replacement roofs wouldn't justify making a set of stamping dies. Are there other photos or can someone who's seen the roofs confirm or deny? My memory is that only one of the Australian makers originally made their own cabs with the other using imported parts, could this explain why the Korean War roofs are only reported on Fords?
|
![]() |
Thread Tools | |
Display Modes | |
|
|