Canvas Side Curtain Frame

[Maurice Donckers]

Here pictures of side screen , These NOS ones have an aging problem with the plastic widows.

[Maurice Donckers]

Here the side screen out of wraping .Next screen left print on screen.

[Bob Carriere]

...... thanks for the wonderful pictures of the infamous "rods" ... this is the first time I have actually seen a full set.

I assume they are solid steel rods and transition to the square/diamond shape at the bottom....... can you give us some dimensions..... diam. length, etc.

Have you considered undoing the stiching (very carefully ) of the windows/celluloid and restitching by hand with new vinyl windows.....? I have originals NOS curtains like you but the clear plastic is seriously fogged over and brittle with age.......

Bob C.

[Grant Bowker]

Bob, look at the right hand photo again. The top (horizontal) rod looks to have slightly larger, tubular downward tips to hold the tops of the vertical rods. I think the horizontal rod should be inserted to the canvas first, then the verticals slid into the pockets. Does this theory match the reality if the sizing of the canvas?

[Maurice Donckers]

I Stiched new window plastic in the ones I have in the truck . I also have a set wich is collored in a dark desert yellow . And I have from the same material a radiator cover.
The rods are solid and round even at the bottom .there are little tubes welded on the top ones corners, so you can slide the upright ones in .
if they are mounted , the screen is a nice tight fit in the cab , but if you unbucle the 3 doorfasteners , and lift it out the two upright ones fall out of the bottom of the screen . In practice they went in the mud , to not be botherred about anymore . You have to take the 3 rods out off screen so you can fold screen double and put it together with the rods in the bag behind driver.

[Jim Price]

The screen I obtained from Brian Asbury is a bit different from the ones I've seen in this thread. It has a different sized set of "windows' that the one Maurice has but the same as Chuck's. However, There are three"cinch" type fasteners that attach the bottom of the curtain to the door. Please see the pictures below.

Another conundrum: When I got my truck there were ring snaps along the top of the door frame. My body guy dutifully replaced them when replacing the wood framing. What was their purpose? Is there a third "flap" that snaps on there? See the picture.

Regards,
Jim

[Mike K]

Originally Posted by Maurice Donckers

The rods are solid and round even at the bottom ..

Maurice, may be a misunderstanding, but that doesnt make sense as the door fittings for the rods are square/diamond shaped , unless the door fittings are of two types ... mystery goes on.
Mike

[cletrac (RIP)]

Here's a couple of factory pix of the side curtains. You can see the top snaps on the inside pic.

[Ganmain Tony]

Originally Posted by Maurice Donckers

I Stiched new window plastic in the ones I have in the truck . I also have a set wich is collored in a dark desert yellow . And I have from the same material a radiator cover.
The rods are solid and round even at the bottom .there are little tubes welded on the top ones corners, so you can slide the upright ones in .
if they are mounted , the screen is a nice tight fit in the cab , but if you unbucle the 3 doorfasteners , and lift it out the two upright ones fall out of the bottom of the screen . In practice they went in the mud , to not be botherred about anymore . You have to take the 3 rods out off screen so you can fold screen double and put it together with the rods in the bag behind driver.

I noticed in one of your earlier posts Maurice you appear to be the proud owner of the side curtain rods for the 11/12 Cabs.

Are you able to provide some measurements of these? Just length and diameter would be really really useful.

Please??

[Ganmain Tony]

The fasteners at the bottom of the side curtains that clip it onto the door are these in the picture.

The ones that go into the door are A81002

Used om T-Model Fords.