![]() |
|
#1
|
|||
|
|||
![]()
G'day all,
A while back I purchased what I assumed was a cab 13 F15A to use the V8 for another project. After speaking to another blitz owner, he mentioned that CMP might have been a gun tractor. I'm a bit of a noob when I comes to CMPs and having no body numbers to go off I thought you guys could give me a yes/no answer? Cheers Luke |
#2
|
|||
|
|||
![]()
Your truck has some features that are not standard on 15 cwts (at least based on my mainly Chevrolet experience) 20" wheels, helper/overload springs, winch, cable guide under rear of frame, transfer case with PTO for winch.
All of these features should be on a gun tractor but could also result from a larger truck being cut down to better suit its post-war use. Look for signs of frame modification to take a better guess - my thought is that the external reinforcement is probably due to the crane added. The cab floor may also give help. do the openings for transfer case shift lever look factory or "gas-axe" made? |
#3
|
|||
|
|||
![]()
[QUOTE
The cab floor may also give help. do the openings for transfer case shift lever look factory or "gas-axe" made?[/QUOTE] Hi Luke, As Grant said there are a lot of pointers to a gun tractor chassis and the floorboard would be a good indicator if it was an original F15A with the single speed xfer case. As shown on the attached photo the F-15A floor has just a single notch beside the fuel tank selector valve for the transfer case selector lever and no hole in the floor to the left of the valve where the two speed lever would be. If you have a slot, and a hole, for the two levers it definitely was a "gas axe" job. I had an F-15A with a two speed xfer case and 20" wheels but that was not an uncommon civilian mod. The holes on the crossmember where the transfer case attaches to it were also elongated to fit the larger 2 spd xfer case mounting pattern which is another giveaway that it was originally an F-15A chassis. Another indicator would be the diff markings. An F-15A has the ratio "6-39" (pinion-crown gear teeth) stamped on the diff housing opposite the pinions of the diffs and vehicles with original 20" wheels have "6-43" stamped at that position, 6-5:1 versus 7.16:1 ratios. There a few a few gun tractor specialists on the forum who no doubt can shed more light on it. I'm hoping it is a gun tractor. Cheers,
__________________
F15-A 1942 Battery Staff Jacques Reed |
#4
|
|||
|
|||
![]()
What's the chassis number? (top of right hand chassis member, adjacent to the engine mount cross member)
That should simplify matters. The Aust gun tractors are easy enough to locate in AWM126 (now online). Start trawling, Luke!! Mike ![]() |
#5
|
||||
|
||||
![]()
Is there a ammo box mounted in the passenger side of nose cone ?
Any evidence of a mount on passenger side wheel arch inside ? Engine chassis number sometimes found on bellhousing of gearbox at the top as well (If it is original gearbox ) Australian Gun tractor don't have the helper springs but easily added on later
__________________
Have a good one ![]() Andrew Custodian of the "Rare and Rusty" ![]() |
#6
|
||||
|
||||
![]()
The double rear cross member and fairleads marks this as a winch equipped (=FGT) chassis.
As Mike suggested find the chassis number!
__________________
Film maker 42 FGT No8 (Aust) remains 42 FGT No9 (Aust) 42 F15 Keith Webb Macleod, Victoria Australia Also Canadian Military Pattern Vehicles group on Facebook https://www.facebook.com/groups/canadianmilitarypattern |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
F15A with 6-pdr | Hendrik van Oorspronk | The Softskin Forum | 23 | 28-02-24 10:19 |
f15a WT 2k1 | Dennis Gelean (RIP) | The Softskin Forum | 0 | 30-12-09 06:53 |
F15A KL | Don Birnie | The Softskin Forum | 6 | 29-11-05 02:13 |
'43 f15a | John McNarry | The Softskin Forum | 20 | 27-02-05 16:09 |
F15A For Sale | J Caldwell | For Sale Or Wanted | 0 | 15-12-04 15:57 |