MLU FORUM - brake rod

MLU FORUM (http://www.mapleleafup.net/forums/index.php)

- The Carrier Forum (http://www.mapleleafup.net/forums/forumdisplay.php?f=6)

- - brake rod (http://www.mapleleafup.net/forums/showthread.php?t=24604)

HI ALL,
I need to restore that long brake rod that rhat goes all the way to the brake
I need to know the exect length of this rod??
thnaks

I don't know the length of the rod Arie but I had a friend that made new rods for his carrier using metric material as imperial was no longer available. The metric rod was undersize. As a result the thread was not full depth and a rod end pulled off when steering was applied. When that happens you not only lose steering to that side of the vehicle, the action of the equaliser linkage ensures that you have no brake pedal function at all. The pedal just goes to the floor as the linkage pulls the failed rod.
It is absolutely critical that you get this right as if one rod end fails the only braking you have is steering input to the other side so long as it doesn't fail also.

David

Just a shade over 84-3/4" long. I was going to say 85 or so, but decided to go to the one I have on the floor now and remove the end linkage to get you a more exact measurement.

When you get your brake gauges to do the adjustment, you'll realize that you have a little wiggle room to these, as the ends are threaded for about 1-3/4 length.

Plenty of imperial rod here in Canada. I know I would have more problem finding metric.

I expect Lynn is about to log on, it being Saturday morning there and Friday evening here... perhaps he will say this information is in the control rods thread?

See: http://mapleleafup.net/forums/showpo...65&postcount=1

84-3/4" = 2152.65mm. Close enough to 2153mm

__________________________________________________ _________________________________________________

Quote:

My idea here is to make this thread a resource of info for the various control rods in the standard MkI U.C.
Most of the rods are medium tensile 7/16" dia. with BSF threads (the throttle control rods are smaller)
If I have any measurements wrong please advise, and I will edit my mistakes.
It maybe be that correct lengths are in a parts book, and if so, someone might like to put all of them up here.
Until then, here are the finished cut lengths of some, to start with;

There are essentially eleven rods;
Five for the brakes,
Two to hold the power unit to the rear plate,
Two clutch rods, and
Two throttle rods (1/4" dia.)

The LONGEST brake rods are both the same (TL5014) length at 2153mm overall length, with 32mm of thread at each end.
The transverse rod (TL 2332) is 646mm overall length with 45mm of thread at each end.

The front clutch rod (TL2328) is 1125mm long overall length, with 60mm of thread at one end, and 40mm at the other
The rear clutch rod (CTL7111) is 1078mm overall length, with 32mm of thread at each end.

The two throttle rods;
the long one is 1040mm overall length, with each end having about 25mm of thread. (rear?)(CTL7112)
the short one is 973mm. thread as above (front?)(CTL2744)
Which ever is the rear one may vary due to different throttle bell crank arrangements with 21 and 24 stud motors. The front rod is the same in all applications.

The engine tieback rod (TL 881) is 585mm overall length. It has 40mm of thread at one end, and 110mm at the other.
It has a kink at each end, about 100mm in.

With regards the cam control rods, the length of the rod from tip of the thread to the center of the pin (long clevis end) is 687mm. this includes the 35mm of thread. This would be the total of CTL 2881 and CTL2882 (1941 parts book) if both were riveted together as one assembly (and any adjustment would be made at the small clevis end. This is here so that someone can make up their own rod assemblies using original clevises. I hope its all clear?

The short brake rods are 250mm overall length. I have 35mm thread on one end and 40mm on the other. I made this rod some years back so these dimensions will need to be confirmed.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.II. L.P.(1)
DodgeWC55.37mmGun Motor Carriage M6
Jeep Mb/Gpw

His measurement of 2153 mm works out to 84.76378 inches when I do the conversion on google. So when I said a shade over 84-3/4, I sure wasn't out by much.

Shame all of Lynns measurements are in some cryptic measurement system rather than good old inches and fractions.

Quote:

Originally Posted by rob love (Post 215074)

Ah, but what side of the road do they drive on?
I read they can privately own firearms too? How novel. :cheers:

UPDATE: how time changes things...

THANK, this is very helpfull
arie

Rob, I have to ask "At which point did decimal points get introduced into "good old fractions"?"
If you're pretending to be a purist you'll have to try harder :)

I was going to say we Canadians do it both ways, but thought better of it.

In which case, I too would just suffer the criticism about the decimal point. :)

HI, It is not clear to me, what is the legth of the cam rod CTL 2881??
thanks
arie

Arie search all of my threads under my name and youwill find a thread about all the rods. Haven't we been there before?