MLU FORUM

MLU FORUM (http://www.mapleleafup.net/forums/index.php)
-   The Carrier Forum (http://www.mapleleafup.net/forums/forumdisplay.php?f=6)
-   -   Carurettor choke control (http://www.mapleleafup.net/forums/showthread.php?t=31894)

Tom Millward 11-01-21 13:07

Carurettor choke control
 
Hi all,

Does anyone have a picture of how the carburetor choke control interfaces to the carb? I've searched the forum and the workshop manual but can't find any detail.

Also, I think my dynamo regulator is on the blink as the charging light is permanently on at idle and it takes quite a few revs to turn it off. The voltage at the battery with the engine running is also erratic. What regulators do people use? I believe my dynamo has been converted to 2 brush and is 12V.

Thanks in advance.

Tom

kosbie 11-01-21 14:18

Hi Tom
I have used repro Lucas regulators from Auto Electrical Supplies in the UK on My MkI and on a couple of trucks and they have worked fine and look just like the originals.
I think the choke connection will depend a bit on what carb you are using?
Rick

Ron Pier 11-01-21 14:53

3 Attachment(s)
As Rick suggests, it depends which carb you have. This is mine, but I don't know if I have the correct carb, it was the one that came with the carrier and I had to jury rig the cable like this. I've always thought that it's odd to have to loop it round, but it and the carb work fine. Judging by the spade terminals, I guess my regulator must be post war. I've converted to 12V and again it works fine. If a period looking 12V regulator with screw terminals dropped in my lap I'd swap it. Ron

Petr Brezina 11-01-21 15:53

1 Attachment(s)
Hi Tom, Im using Zenith carburetor which is French copy of Stromberg 97. I had to adapt choke control to this carb and its working fine. Please see picture for inspiration.

Tom Millward 11-01-21 16:53

Thanks for the pictures gents. It looks like I have a replacement carburetor, as it doesn't have the limiter on it, so I'll have to get creative with some brackets like Petr has.

I'll also get a Lucas style regulator on order. I had looked at some solid state ones, which also say they prevent discharging at idle, but they are quite expensive.

I'll post some updates when I've rigged something up. Just the brakes and steering to adjust now and I'll be taking out on the road for the first time!

Cheers,

Tom

Lynn Eades 11-01-21 22:12

Is your generator ford or lucas. If ford (you say it has been converted to a 2 brush) then you will need a regulator suited to the ford (I think) Suggest you take yout generator AND regulator to the auto electrician and get him (her) to sort it out.

Tom Millward 11-01-21 23:06

Hi Lynn, how do I tell if it’s Ford or Lucas, will it be marked with either name? I think I need to get it off the engine and have a look.

Lynn Eades 12-01-21 09:56

Lucas is longer, has Lucas, model (C42x or C45x) voltage, direction of rotation, year and month. stamped in the case. Ron's regulator is a Lucas RB108 (or similar) The Lucas can be converted to 12 volt by fitting the correct 12 volt armature (if you could find one)
The above statement is wrong. Brain fade.
The Lucas generator is converted to 12 volt by changing the 6v field coils for 12 v field coils. The 6v armature works fine in a 12 volt system (but a 12 volt one cant cope in a 6v system)

Tom Millward 12-01-21 11:22

Thanks Lynn, my Carrier came from Andrew Rowe over in your part of the world. I believe that he changed the field coil windings to 12V ones. I will go and check what type of generator I have fitted.

In relation to your earlier point of taking it to an auto electrician, I don't know that they exist in the UK anymore. Everything now is repair by replacement, I may be wrong, but finding someone with experience with dynamos and regulators will be quite hard now.

I'm ex REME, and even in the Corps the skills of being able to adjust or repair equipment as opposed to replacing it are no longer taught at the REME trade schools. I think so much equipment is become sealed boxes that there is nothing for technicians to do anymore other than diagnose and replace sealed boxes. Hence the skills are being lost. Which is fine until you can't get the spares!

Ron Pier 12-01-21 15:59

As far as I know, my dynamo is still 6 volt, but still charges a battery at a decent rate through the regulator. (I know Jeep owners often convert to 12V but still use the same dynamo....Even the starter motor I've heard?) My starter motor is a 12V unit and of course so are all the bulbs. An electronics friend made up resistors for the gauges, although I've never got the fuel gauge to work......Yet. Ron

Andrew Rowe 12-01-21 18:21

12 Volt Gen.
 
Hi Tom, The gen, should be a Standard Ford Housing and armature and using Lucas C45 Field coils. The regulator was matched for 12 volt for this application.
I would suggest , you can probably increase the charge rate by adjusting the regulator output, Cheers Andrew

Lynn Eades 12-01-21 20:43

I have edited my previous post. Tom's following comment prompted me, that I mis-led you. Refer to my above post. Basically the resistance of the field windings is different between 6 and 12 volt. Conversion can be carried out by having new field windings wound.
Tom you just need to find an older Auto electrician. Go on line. In England there is a company that rebuild these older lucas units. They make up new field coils and rewind armatures.
I could spend time doing it, but so can you.

Mike Gurr 12-01-21 22:24

1 Attachment(s)
Tom,
Do you have any idea what carb your Carrier should have? Mine has the original Zenith with governor fitted but is a Canadian Mk2, I think from memory yours is a Mk1? I do have a spare Zenith if that would be correct for yours.
Mike

Tom Millward 13-01-21 10:00

Hi Mike, I very much appreciate the offer of the carb. I'll try and get the engine covers off today and get a picture of it, and then the forum can let me know if it's correct or not. I don't think it's the same as yours though as I remember discussing the governor with you and I don't think mine looks like it has one.

Tom Millward 13-01-21 10:02

Quote:

Originally Posted by Lynn Eades (Post 275697)
I have edited my previous post. Tom's following comment prompted me, that I mis-led you. Refer to my above post. Basically the resistance of the field windings is different between 6 and 12 volt. Conversion can be carried out by having new field windings wound.
Tom you just need to find an older Auto electrician. Go on line. In England there is a company that rebuild these older lucas units. They make up new field coils and rewind armatures.
I could spend time doing it, but so can you.

Thanks Lynn, I'll have a google and see what I can find. I'm assuming that the regulator can be adjusted to match the output of the dynamo then? I'll also see if I can find instructions on line as I have a voltmeter and always like to try and learn new skills.

Lynn Eades 13-01-21 19:14

Tom, a 12 volt generator unregulated will put out 50+ volts, but it wont last long. If you can take both units out then a specialist is the way to go.
Go here Tom. http://www.dynamoregulatorconversions.com
and more http://www.spitui.com/regulator.html


All times are GMT +2. The time now is 14:59.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016